Thanks all for the replies. I am in contact with Zeropoint0.5 and I will let him take
a look at my amps. It will take a while before my new install will happen but, I will post
my install here on this forum.
Thanks again,
Jeroen
Search found 15 matches
- Fri Oct 03, 2014 4:23 am
- Forum: Car Audio
- Topic: ZPA 0.3 bridged on 1 TI10d 4ohm
- Replies: 17
- Views: 6831
- Tue Sep 30, 2014 9:44 pm
- Forum: Car Audio
- Topic: ZPA 0.3 bridged on 1 TI10d 4ohm
- Replies: 17
- Views: 6831
Re: ZPA 0.3 bridged on 1 TI10d 4ohm
Its coming from the ZPA outputs.Is the noise your getting coming from the ZPA's outputs? Or the ZX400, kinda confused there. Is the ZPA causing the turn on/off pop/thump, you can determine by removing the RCA's then powering it up.
- Tue Sep 30, 2014 11:56 am
- Forum: Car Audio
- Topic: ZPA 0.3 bridged on 1 TI10d 4ohm
- Replies: 17
- Views: 6831
Re: ZPA 0.3 bridged on 1 TI10d 4ohm
They have 11 blades... I have issues with 1 of the zpa's. Its working but, noisy over the speakers that I have connected on the ZXti 400.2 when its powered on. And there is a loud noise when turned on and off. I am reading alot here on the zpa's about new caps. I have taken it apart and I am cleanin...
- Tue Sep 30, 2014 9:06 am
- Forum: Car Audio
- Topic: ZPA 0.3 bridged on 1 TI10d 4ohm
- Replies: 17
- Views: 6831
Re: ZPA 0.3 bridged on 1 TI10d 4ohm
I have a PLD and a BassCube.
On the pcb of the zpa is printed rev B. Does that mean that it is a V2?
On the pcb of the zpa is printed rev B. Does that mean that it is a V2?
- Mon Sep 29, 2014 10:26 am
- Forum: Car Audio
- Topic: ZXti 400.2 leds
- Replies: 18
- Views: 7521
Re: ZXti 400.2 leds
Ok did the test... and yes 2 of the leds are faulty.
Thanks again.
Are there any specs on the leds. Maybe I can get
them at a local store?
Thanks again.
Are there any specs on the leds. Maybe I can get
them at a local store?
- Mon Sep 29, 2014 10:13 am
- Forum: Car Audio
- Topic: ZXti 400.2 leds
- Replies: 18
- Views: 7521
Re: ZXti 400.2 leds
Thanks for the help. I don't know how to test them.
It must be a faulty led. The pcb is powered and the resistor
is ok.
It must be a faulty led. The pcb is powered and the resistor
is ok.
- Mon Sep 29, 2014 9:26 am
- Forum: Car Audio
- Topic: ZXti 400.2 leds
- Replies: 18
- Views: 7521
ZXti 400.2 leds
Hi there,
Next to my 2 ZPA's I also have a 400.2
The amp is running fine but the leds are not working. I measured the pcb on the top with the leds on it.
29 volts on the powerlines and 100 ohm on the resistor.
Does anybody have any experience with this?
Next to my 2 ZPA's I also have a 400.2
The amp is running fine but the leds are not working. I measured the pcb on the top with the leds on it.
29 volts on the powerlines and 100 ohm on the resistor.
Does anybody have any experience with this?
- Sat Sep 27, 2014 7:06 am
- Forum: Car Audio
- Topic: ZPA 0.3 bridged on 1 TI10d 4ohm
- Replies: 17
- Views: 6831
Re: ZPA 0.3 bridged on 1 TI10d 4ohm
Ok ok thanks for the info...
I have build a vented box as PG recommendations.. So I will not do that.
I have build a vented box as PG recommendations.. So I will not do that.
- Sat Sep 27, 2014 4:00 am
- Forum: Car Audio
- Topic: ZPA 0.3 bridged on 1 TI10d 4ohm
- Replies: 17
- Views: 6831
Re: ZPA 0.3 bridged on 1 TI10d 4ohm
Thanks capea4
I had them checked about 2 years ago. After that I havent't used them much.
In the specs of the ZPA's on the PG site I have read that if you snap some diodes on the amp that they deliver more power.
Is that wise to do?
I had them checked about 2 years ago. After that I havent't used them much.
In the specs of the ZPA's on the PG site I have read that if you snap some diodes on the amp that they deliver more power.
Is that wise to do?
- Sat Sep 27, 2014 3:37 am
- Forum: Car Audio
- Topic: ZPA 0.3 bridged on 1 TI10d 4ohm
- Replies: 17
- Views: 6831
ZPA 0.3 bridged on 1 TI10d 4ohm
Hi there,
I have two ZPA's 0.3 and two TI10d 4 ohm subs. I would like to run each ZPA on one TI10d.
To get the most power do I have to connect the speaker terminals in parallel on the subs and then wire to the amps
in bridged mode? Then they are in 2 ohm load right?
regards,
Jeroen
I have two ZPA's 0.3 and two TI10d 4 ohm subs. I would like to run each ZPA on one TI10d.
To get the most power do I have to connect the speaker terminals in parallel on the subs and then wire to the amps
in bridged mode? Then they are in 2 ohm load right?
regards,
Jeroen
- Tue Jan 01, 2013 1:35 am
- Forum: Car Audio
- Topic: phoenix gold ti10d sub enclosure
- Replies: 9
- Views: 5186
- Mon Dec 31, 2012 8:36 am
- Forum: Car Audio
- Topic: phoenix gold ti10d sub enclosure
- Replies: 9
- Views: 5186
Re: phoenix gold ti10d sub enclosure
@dvnt88 the manual you gave is not them. The ones i have are the same as the ti2's but without the leds.
- Mon Dec 31, 2012 8:29 am
- Forum: Car Audio
- Topic: phoenix gold ti10d sub enclosure
- Replies: 9
- Views: 5186
Re: phoenix gold ti10d sub enclosure
First i had 2 xmax 12" woofers on 1 zpa 0.3. They broke down after 15 years. So i bought these ti's. Bought a second zpa 0.3. I have build them in the box i had for de xmax''s... sounds great and loud as you guys mentionend, but i think it can be much better if i build the right box for them. I...
- Sun Dec 30, 2012 5:27 am
- Forum: Car Audio
- Topic: phoenix gold ti10d sub enclosure
- Replies: 9
- Views: 5186
Re: phoenix gold ti10d sub enclosure
the old ones without the leds
- Sun Dec 30, 2012 5:16 am
- Forum: Car Audio
- Topic: phoenix gold ti10d sub enclosure
- Replies: 9
- Views: 5186
phoenix gold ti10d sub enclosure
Hi there,
I want to build a new box for my ti10s. I am running them each of a zpa0.3 ... if maybe anyone can tell me what is the best volume sealed and ported and if ported what is the best volume of the port?
thanks in advance...
greets from Holland
Jeroen
I want to build a new box for my ti10s. I am running them each of a zpa0.3 ... if maybe anyone can tell me what is the best volume sealed and ported and if ported what is the best volume of the port?
thanks in advance...
greets from Holland
Jeroen