Search found 1174 matches
- Tue Nov 07, 2023 3:56 pm
- Forum: Car Audio
- Topic: A little ZX600Ti mod...
- Replies: 35
- Views: 29377
Re: A little ZX600Ti mod...
The zx600 is ±40Vdc primary rails, the same as the 475/500.4. Your auxiliary drive rails should be closer to ±10V referred to the primary rails. If you are only at ±2V, the amp will run but it won't be able to hit full output power because it won't be able to swing the outputs rail to rail.
- Sun Oct 08, 2023 3:45 pm
- Forum: Car Audio
- Topic: Remote for old school Phoenix Gold Bass Cube
- Replies: 18
- Views: 15341
Re: Remote for old school Phoenix Gold Bass Cube
I think I spoke to you on Facebook, but yes, we still make the remotes.
- Thu Oct 05, 2023 5:52 am
- Forum: Car Audio
- Topic: ZX475ti amplifier
- Replies: 3
- Views: 4198
Re: ZX475ti amplifier
If some of the steering LEDs are out, they are either faulty, which often happens with these I finally found the actual problem, it was caused by two of the RED LED lights were defective, I had some in stock and replaced them, one per each channel affected, and the Bias was back again and able to b...
- Sat Sep 30, 2023 1:15 pm
- Forum: Car Audio
- Topic: Resistor Value
- Replies: 1
- Views: 3626
Re: Resistor Value
I assume this is in reference to your other question, R935 on the power supply daughter card is 681R. This resistor is the current limit for the Opto-isolator which mutes the poweramp. If it's faulty all channels will be muted, not two. See my reply to your other post explaining the likely fault con...
Re: Schematic
PG never publicly released any schematics but a few still made it out into the wild. AAMP bought the name and all the IP, so you can ask if they will share. All of the top tier PG poweramps are essentially the same just scaled for different power levels. The ZX, zxti, and ti line are very similar wi...
- Fri Sep 29, 2023 12:18 pm
- Forum: Car Audio
- Topic: Ti600.2 Customs for a client
- Replies: 4
- Views: 5747
Re: Ti600.2 Customs for a client
It all very much depends on what mosfets you choose. There isn't a super simple answer to this question. If you use the fairly popular irf3205, then you should use gate resistors of somewhere around 30R. In the case of a ti500.4 the 33R gate resistors will be fine with irf3205s. Not all PG amps have...
- Fri Sep 29, 2023 12:10 pm
- Forum: Car Audio
- Topic: Zx475 titanium repair
- Replies: 2
- Views: 7042
Re: Zx475 titanium repair
I am looking for assistance in repairing my zx 475 there is something missing off the board and I'm hoping that someone could tell me what it is thank you for any help, or if there is a repair shop close to me I live in renfrew Ontario, the area on the board is C41 I would appreciate any help pleas...
- Fri Sep 29, 2023 12:02 pm
- Forum: Car Audio
- Topic: ZX475ti amplifier
- Replies: 3
- Views: 4198
Re: ZX475ti amplifier
If some of the steering LEDs are out, they are either faulty, which often happens with these, or you will have open fusible resistors in those channels. Normally in either case the output will not only be low, but also distorted. There are fusible resistors scattered throughout every PG amp. They wi...
- Tue May 23, 2023 5:04 am
- Forum: Car Audio
- Topic: Ti2 1000.4
- Replies: 2
- Views: 6906
Re: Ti2 1000.4
It sounds like your question is about a kenwood head unit, it has little to do with the amp. You should probably reach out to customer service wherever you bought the gear from. It's difficult to even understand your question...
- Sun Apr 09, 2023 8:57 am
- Forum: Car Audio
- Topic: Who needs a bass cube knob?
- Replies: 103
- Views: 92549
Re: Who needs a bass cube knob?
I just ordered more parts yesterday. You can email me from the email link on the phorum here. It's the best way to get me quickly.
I was on vacation the last week of March through last week. I'll be back at the shop tomorrow.
I was on vacation the last week of March through last week. I'll be back at the shop tomorrow.
- Sun Apr 09, 2023 8:55 am
- Forum: Car Audio
- Topic: Remote for old school Phoenix Gold Bass Cube
- Replies: 18
- Views: 15341
Re: Remote for old school Phoenix Gold Bass Cube
I think that I've spoken with him via Facebook. At least someone contacted me asking for 4 remotes. The Email link for me on this phorum will email my shop address directly. It's the quickest way to reach me. After that either fb message or pm here. I just ordered more parts for remotes, so we are s...
- Sun Mar 19, 2023 4:20 am
- Forum: Car Audio
- Topic: This place has been crazy dead... I think I hear an echo
- Replies: 9
- Views: 12265
This place has been crazy dead... I think I hear an echo
... Echo... echo...
It's like a graveyard in here. I'm only posting this to see if the phorum is actually broken. I can't believe it's been 6 months since they're had been a post.
Later,
Jason
It's like a graveyard in here. I'm only posting this to see if the phorum is actually broken. I can't believe it's been 6 months since they're had been a post.
Later,
Jason
- Tue Sep 20, 2022 3:56 am
- Forum: Car Audio
- Topic: Who needs a bass cube knob?
- Replies: 103
- Views: 92549
Re: Who needs a bass cube knob?
Yes, we still make them. PM and I'll reply much faster than a phorum message.
- Tue Sep 20, 2022 3:54 am
- Forum: Car Audio
- Topic: Bass Cube Remotes
- Replies: 219
- Views: 152755
Re: Bass Cube Remotes
We still make them, but probably not fit much longer. I'm almost out of the specialty gain pot and I've not been able to source more.
- Thu Apr 28, 2022 7:04 pm
- Forum: Car Audio
- Topic: Working on an Orion HCCA-d1200
- Replies: 4
- Views: 8463
Re: Working on an Orion HCCA-d1200
I'll look next time I'm in the shop and remember. I'm not sure where it is, but I should still have the schematics I doodled. I'll do my best to remember to look for it
- Mon Apr 11, 2022 3:46 am
- Forum: Car Audio
- Topic: RX 600.5 Reverse polarity diodes Help please!
- Replies: 1
- Views: 5272
Re: RX 600.5 Reverse polarity diodes Help please!
1N5400.
Any standard 3a rectifier with a >50V rating will work fine though. Their only job is to go short circuit when reverse polarity is applied. Kind of the opposite of a fuse to ensure the actual fuse does go open
Any standard 3a rectifier with a >50V rating will work fine though. Their only job is to go short circuit when reverse polarity is applied. Kind of the opposite of a fuse to ensure the actual fuse does go open
- Mon Apr 11, 2022 3:36 am
- Forum: Car Audio
- Topic: PG M50 Where to find PS rectifier specs
- Replies: 2
- Views: 5369
Re: PG M50 Where to find PS rectifier specs
If you tried to test the rectifiers in circuit they will always appear shorted. They cannot be tested in circuit as the transformer windings are directly across them. Out of hundred, I can count on one hand the number of PG amps I've had with shorted power supply rectifiers. It almost never happens ...
- Mon Apr 11, 2022 3:33 am
- Forum: Car Audio
- Topic: Who needs a bass cube knob?
- Replies: 103
- Views: 92549
Re: Who needs a bass cube knob?
Yes, we still make them. We've been wading through some deep family shit over the past several months and have not been spending very much time online.
Tyrone, I sent you an email to the address that your friend in FB gave me.
Tyrone, I sent you an email to the address that your friend in FB gave me.
- Sun Sep 26, 2021 6:43 pm
- Forum: Car Audio
- Topic: Who needs a bass cube knob?
- Replies: 103
- Views: 92549
Re: Who needs a bass cube knob?
Yes, I replied to you on diyaudio as well. We will get you set up. Thank you!
- Wed Sep 08, 2021 3:21 am
- Forum: Car Audio
- Topic: phoenix gold zx 450 zx350 potentiometer replacement + caps
- Replies: 11
- Views: 8997
Re: phoenix gold zx 450 zx350 potentiometer replacement + caps
Looking for a replacement capacitor for my zx450 Its 2200uf 16v 105deg C measures approx 18mm x 35mm You need to replace all the stock Panasonic caps in the power supply, not just one. They leak and will eventually cause the amp to catch fire. Other than that, any general purpose low esr cap will w...
- Fri Jul 23, 2021 4:21 am
- Forum: Car Audio
- Topic: Who needs a bass cube knob?
- Replies: 103
- Views: 92549
Re: Who needs a bass cube knob?
I still have bc knobs available. My daughter makes them now, but we still have boards and parts. I've been making them for something like 15 years now. I have lpl44's as well. Pm for details.
Later,
Jason
Later,
Jason
- Tue Jul 13, 2021 3:11 pm
- Forum: Car Audio
- Topic: Titanium 800.1 Cuts out in Hot Weather
- Replies: 1
- Views: 2752
Re: Titanium 800.1 Cuts out in Hot Weather
Iirc the polyswitch thermal sensors are designed to switch at 110° C. Obviously the interior of your car and amp should never be getting hot enough to boil water, sun or no sun. I expect that you still have something going on. In regards to your previous post, there are no transistors involved with ...
- Tue Jun 15, 2021 8:22 pm
- Forum: Car Audio
- Topic: Phoenix Gold Ti2 1300.1 diode
- Replies: 7
- Views: 8992
Re: Phoenix Gold Ti2 1300.1 diode
I've only worked on a few of the newer aamp PG products, but they are almost all common Korean designs with a bit nicer lipstick on them. You are going to have to figure out what is holding it in shutdown. Without a lot more information and without knowing your skill level or available tools, there ...
- Tue May 25, 2021 3:40 am
- Forum: Car Audio
- Topic: PG Titanium 800.1 Stuck in Thermal Protection
- Replies: 4
- Views: 3785
Re: PG Titanium 800.1 Stuck in Thermal Protection
I've never seen a bad thermal sensor on any of these. It uses several ptc polyswitches as thermal sensors. I'd still bet on the trace under the rca connector. It's far more rare and unlikely, but it could be a failing comparator which is used to supervise and trigger the different fault conditions. ...
- Mon May 24, 2021 2:06 pm
- Forum: Car Audio
- Topic: PG Titanium 800.1 Stuck in Thermal Protection
- Replies: 4
- Views: 3785
Re: PG Titanium 800.1 Stuck in Thermal Protection
Was it working previously? Did you or someone else who is not a qualified tech disassemble and reassemble it? For that matter, tech or not, did anyone unfamiliar with these disassemble and reassemble it? If it went into thermal after being opened and then then reassembled, it's almost certainly a br...