http://download.phoenixphorum.com/Manua ... 5x_230.pdf

here's the owners manual.....

http://intl.jlaudio.com/10w7ae-3-car-audio-w7ae-subwoofer-drivers-92114 one sub....on the m100... brigded at 3ohm.....perfect combo......... it is but far from shallow.. 8) is correct.....but just having 0.6 cuft of space will never be enough to fit a sub that can handle the power of a m100.... sha...

http://intl.jlaudio.com/10w7ae-3-car-au ... vers-92114

one sub....on the m100... brigded at 3ohm.....perfect combo.........

my first thought would be it comes out of the crossover board...does it have a green quadpot in it?? those pots caused alot of trouble in the past...... but if you didn't have this noise before cap changing, maybe you did something else wrong..... did you only replace the rail caps ? or did you mean...

never understand collecting amps, storing them for eyes pleasure :) amp is giving a pleasure for my ears and eyes when it's installed correctly with other system parts...lol. Ok you can have a car that never sees winter or wet air...but still, amps have to do their job! guys collect amps, women col...

i would put the m25 on the speakers.....soundwise you hear a difference with the M50...... the m25 just sounds better, especially in the mid and high frequencies....... that leaves you the M50 who will give around 250rms at 4ohm and 360rms at 2 ohm, brigded...... http://intl.jlaudio.com/8w7ae-3-car...

http://www.youtube.com/watch?v=x0p2ZpsvhoU

http://www.youtube.com/watch?v=og8pZ6vcUss

http://www.youtube.com/watch?v=SsPJHv46_8U

lovely little 8inch bastard..................look the little guy go !!!!!!!!!!!!!!

i would put the m25 on the speakers.....soundwise you hear a difference with the M50...... the m25 just sounds better, especially in the mid and high frequencies....... that leaves you the M50 who will give around 250rms at 4ohm and 360rms at 2 ohm, brigded...... http://intl.jlaudio.com/8w7ae-3-car-...

Jeroen, you got a pm................check it out.

alot of things in the zpa are important..... next to replacing the ps caps, upgrading the amp to a V2 version, and even replacing the irfz44 to a irfz48 or something else in the powersupply, having the bias set back to good values...... the zpa will only switch into the high current mode if the amp ...

if you have a zpa0.5 in the future, just use it for speakers.....no amp sounds like this one do, especially in the mid and high frequencies..... yes you can do the mod to lock this amp in the HV mode, but probably the ps fets (irfz44) will fail with the first voltage drop that comes..... those fet'...

Hey VW, Yeah the factory recommended rms is 1200 but it seems widely accepted that it takes more than that to get this sub moving. Have you used the elite 12d? I'd like to hear from guys who have some different setups with it and what their best results were achieved with wattage wise. There is a z...

nice........... i got exactly the same of both....both new in 1998.... enjoyed them for 10years along with a black zx350....... if both amps are recapped you're fine......and new cooling paste also on the fet's / transistors..... one main thing about the zx amps is, that after some years, setting ba...

It may be something as simple as the wrong r-network used. I had a member here send me a PG processor (can't remember model) but ended up being the wrong r-network chip, it caused similar issue.....high pitch noise (around 1khz) on all of the outputs. witch one are "the wrong R-nets" ?? t...

It may be something as simple as the wrong r-network used. I had a member here send me a PG processor (can't remember model) but ended up being the wrong r-network chip, it caused similar issue.....high pitch noise (around 1khz) on all of the outputs. witch one are "the wrong R-nets" ?? t...

Great guy to deal with, did an effort to make a careful packaging,

so the zpa0.5 , tbat and pld1, all in white arrived at me in the same condition it was shipped.....

i would deal with him again for sure............

thank you David

second of all ,, don't forget the fan's also blow air to the vertikal daughter boards....

if that is gone some resistors will probably overheat and burn............

i understand very good the problem about the noisy V2 adda fans..... the fans are good......for an amp that is driven hard and playing loud all the time.... i have found a little solution in this.... in some of my zpa's i brought back an panaflo fan or a alternative orion model i found on mouser.......

I recapped this ZPA and gave it a little try. First thing I noticed is that the DC offset has changed from 11/15mV to about 30/50mV. This puzzles me, because I havent touched the bias pots. I did remove and reinstall the heat sinks. Also the fans werent connected when I measured DC offset. SO maybe...

As far a crossovers I think the only big differences is the ability to bi amp. By this I mean to be able to band pass the rear channels on the ti. The zx can do the x10 but is a high pass on the rears. Now of you run a high pass signal in you could low pass the rear channels and do the same thing. ...

GUTS What's the capacitance for the rail caps on the MS275? I scored one yesterday off of CL and I was quite surprised to find a large pair of 35v 15,000uf caps. i also have 2 ms275 with railcaps simular like this in it.........maybe PG was out of stock that time and they putted these in that momen...

3 crossovers with exactly the same issue ?? no , probably all 3 are fine and this issue is located somewhere else....... maybe you can solve the issue with taking the B+ for the crossover from another point of where you take it now or take another point in the car for B- also...... about the switch ...

I would replace the 8 ps caps to be sure.....i wouldn't trust those....

wasn't this amp 2 zx400ti, basscube and ti powercore all in one ??

you took a big risk by powering the amp up first of all.............you're a Lucky man nothing happened.... please recap it first............... can you measure one time the value of those big resistors on the vertikal daughterboard ?? are they 270ohm of 330ohm ?? a line driver will benefit for sure...

Nils, do you have a link of the gain pots you ordered ?? (and the bassboost pots also maybe) ?? did you already tested those and do they work correctly ?? i once ordered some alps pots and the internal connection of the pins was not right..... for the rest :clap: :clap: :clap: :clap: :clap: :clap: :...