71 Blazer install finally started

teamradrz1 · Post by **teamradrz1** » Sun Jun 21, 2009 5:38 pm

Still working on my Blazer project, but I started the stereo install.

So far I wired in the deck and the 1/0. Made the console bottom plate with the Powercore, TLD66 and base cube. Then made my false floor amp rack for the 2 X1200.1s and the X200.4 ran all the power wire in the rack. Still have lots of work to do but a good amount got completed for 1 days worth of work.

Ok enough with the chit chat on with the pix!

tonym · Post by **tonym** » Sun Jun 21, 2009 6:13 pm

looking great...

Post by **ttocs** » Sun Jun 21, 2009 7:06 pm

looks good so far. Are you concerned that the TLD being right next to the power core might pick up some noise? I always try to seperate power and signal and I don't know if I have ever known of a power core that close to a line driver. they are normally in the back just to keep them close to the amp.

Post by **Rold Gold** » Sun Jun 21, 2009 7:56 pm

nice........................

teamradrz1 · Post by **teamradrz1** » Sun Jun 21, 2009 8:36 pm

Not sure if they are too close if I have noise I can always move it somewhere else I was planning on hiding those devices anyway and put a plexi just above the powercore at the bottom of the cosole chamber floor.

Misfire · Post by **Misfire** » Mon Jun 22, 2009 6:25 am

Can't wait to see it complete. My friend had a 73 blazer and dam did we do some stupid ass off roading/in town smashing! He had a 305, what's in yours?

Post by **stipud** » Mon Jun 22, 2009 6:58 am

Nice and tidy. So far so good! Keep those pics rollin

teamradrz1 · Post by **teamradrz1** » Mon Jun 22, 2009 7:18 am

Misfire wrote:Can't wait to see it complete. My friend had a 73 blazer and dam did we do some stupid ass off roading/in town smashing! He had a 305, what's in yours?

Chevy crate 350 w/275HP but then added Edelbrock cam, lifter and intake package, gear drives and alum roller rockers so should be about 300 HP.

Post by **Bfowler** » Mon Jun 22, 2009 1:46 pm

nice....i like where this is going!

Pedi · Post by **Pedi** » Mon Jun 22, 2009 3:13 pm

Nice rack..

teamradrz1 · Post by **teamradrz1** » Mon Jun 22, 2009 4:29 pm

Pedi wrote:Nice rack..

DITTO!

reallyxxxxxxloud · Post by **reallyxxxxxxloud** » Tue Jun 23, 2009 2:02 am

here in Australia to say nice rack is to say nice tits (.)(.) ...

But it is a nice rack!!!!

Post by **ttocs** » Tue Jun 23, 2009 5:40 am

I think that is universal, that is why it was soo funny.

teamradrz1 · Post by **teamradrz1** » Tue Jun 23, 2009 7:17 am

ttocs wrote:I think that is universal, that is why it was soo funny.

And why I said ditto which means copy or same, looking at Pedi's avatar

Post by **Bfowler** » Tue Jun 23, 2009 10:47 am

so you need the rubber boot for the power part of the xenon amp?

teamradrz1 · Post by **teamradrz1** » Tue Jun 23, 2009 11:13 am

yes I need 1 boot for the lower right power side /_|

teamradrz1 · Post by **teamradrz1** » Tue Jun 23, 2009 10:11 pm

OK made the boxes for the TiD Elites and welded up my seat frame so I can run the 04 Tahoe 3rd row 50/50 split bench in the rear.

wash with gasoline · Post by **wash with gasoline** » Wed Jun 24, 2009 12:04 am

thats the nicest blazer iv seen, cant wait to see finished pics. ...fing miss my full size stuff