CES 2013 Sneak Peek ?

J.Wright · Post by **J.Wright** » Mon Jan 07, 2013 4:24 pm

With CES starting next week... Any sneak peeks or hints....?

Post by **AVICJR** » Mon Jan 07, 2013 6:32 pm

J.Wright wrote:With CES starting next week... Any sneak peeks or hints....?

Post by **ttocs** » Mon Jan 07, 2013 6:39 pm

its a nice thought but you are basically asking a graduate student the week before finals to give you a few mins of their time. It doesn't get any busier then now trying to get everything ready for it all.

J.Wright · Post by **J.Wright** » Tue Jan 08, 2013 4:22 am

Lol.... That's a great analogy....

Post by **ttocs** » Tue Jan 08, 2013 5:03 am

Its like good like trying to find a good install shop on the west coast/south west right now as well. Any good shop was contacted up too a year ago to get a build for ces together. The REALLY good shops had that one, and 4 others offered in the last month that have to be done for ces.

MW3 · Post by **MW3** » Tue Jan 08, 2013 5:07 am

Guys we have a ton of new stuff for this year. Let's start with the Ti2 amplifiers.

These have a very small footprint but deliver a ton of power. The electrical designs are all done in the usa with our electrical engineering team. The full range class D design is really top notch, it uses what we call ADAPT technology. Basically its a rail jumping Class D that jumps up and down to the appropriate voltage rail according to the signal input, very cool. Not to mention a balanced differential front end with very nice Op-Amps. It also uses post filter feedback in the output stage for excellent sound quality. This is one of best (if not the best) sounding full range Class D amplifiers out there.

Also the amplifiers are very conservatively, should we say old school rated. For example the 800.1 is rated at 800w at 1% THD and 14.4 volts. It actually delivers 1150w into that load. The Ti 21600.5 actual power measurements are below, again very conservatively rated.

Sizing:

Ti2 800.1 and Ti2 1000.4 - 11.7” L x 7.1” W x 2.0” H
Ti2 1300.1 and Ti2 1600.5 - 14.4” L x 7.1” W x 2.0” H

Enjoy!

Ti21600.5

Rated Power:
200w x 4 @ 2Ω
125w x 4 @ 4Ω
plus
800w x 1 @ 2 Ω
400w x 1 @ 4 Ω

Measured Power:
250w x 4 @ 2Ω
140w x 4 @ 4Ω
plus
940w x 1 @ 2 Ω
500w x 1 @ 4 Ω

Ti21000.4
250w x 4 @ 2Ω
150w x 4 @ 4Ω

Ti21300.1
1300w x 1 @ 1Ω
900w x 1 @ 2Ω

Ti2800.1
800w x 1 @ 1Ω
600w x 1 @ 2Ω

• Efficient Class D Topology
• Compact Size for Easy Installation
• Balanced Differential Input Circuitry
• Audiophile NJM2068M Operational Amplifiers
• Ultra High Speed IR Class D Chipset
• ADAPT Power Management (Ti21000.4, Ti21600.5)
• Thermal Rollback System Circuitry (Ti21000.4, Ti21600.5)
• 48dB per Octave Subsonic Filter (Ti2800.1, Ti21300.1)
• Crossovers have 41 detents for Exact Frequency Selection
• High Grade Aluminum Shaft Potentiometers
• Surface Mount Component Technology
• RMD - Remote Voltage Display Ready (see pg. XX)
• RBC - Remote Bass Level Control Included (except Ti21000.4)
• Direct Insert Power and Speaker Terminals
• Audio Precision Quality Control Verification
• High Temperature Plexiglass Cover
• Signal Clipping Indicators
• Power Output Birth Certificate

Post by **ttocs** » Tue Jan 08, 2013 9:41 am

nice job morgan looks good. I need to hurry up and install my old RSD amps before I start sweating these new amps anymore...

Post by **stipud** » Tue Jan 08, 2013 10:01 am

MW3 wrote:Ti21600.5

Measured Power:
250w x 4 @ 2Ω
140w x 4 @ 4Ω
plus
940w x 1 @ 2 Ω
500w x 1 @ 4 Ω

J.Wright · Post by **J.Wright** » Tue Jan 08, 2013 10:04 am

Morgan,

Those look VERY nice... Loving the direction PG is moving....

J

Kirghiz · Post by **Kirghiz** » Tue Jan 08, 2013 2:20 pm

Please, please, please make the bluetooth droid app available on the 2013 Elite series.

The new Ti's look sweet!

vladthebad · Post by **vladthebad** » Tue Jan 08, 2013 3:49 pm

If its class d with voltage adjust... Whatr the odds of getting more voltage to run subs at 2/4/6 ohm impedances and still make rated power instead of this 1ohm crap. (Xenon style, maybe a switch to set max voltage instead of sense? With thermal/current detection to drop voltages if people get a bit too gutsy)

I've always felt that anything running at 1 ohm tends to sound a bit muddier than at 4. My ti800.1 sounded a lot louder at 1 ohm, but worlds cleaner at 4. Same subs, same enclosure.

Maybe next year. Not like I'm in the market for any new amps these days anyways. Unless someone has a Ti800.1AL or a 500.4AL they're looking to part with.

Kirghiz · Post by **Kirghiz** » Tue Jan 08, 2013 6:15 pm

Morgan, any additions to the Elite speaker line? Perhaps dual 2 ohm 10" and 12" subs that can run singly off of the 2 and 5 channel Elite amps?

I need a dual 2 ohm 10" Elite pretty bad. Fingers crossed.

MW3 · Post by **MW3** » Tue Jan 08, 2013 9:35 pm

No additions to the Elite speaker line, maybe next year.

dvnt88 · Post by **dvnt88** » Thu Jan 10, 2013 8:06 am

MW3 wrote:No additions to the Elite speaker line, maybe next year.

Morgan - Do you happen to know the MSRP / MAP on the new TI amps and availability to local dealers????

Kirghiz · Post by **Kirghiz** » Thu Jan 10, 2013 9:15 am

With the re-vamp of the Ti line amps to be full range class D and compact, what does this mean for the SD line? Seems like the Ti line is becoming what the SD line is/was. Are they going to replace the SD's, or are they just going be a higher grade of amplifier?

soundbit · Post by **soundbit** » Thu Jan 10, 2013 10:34 am

hmmm ti going to full range class D. no more Triple-Darlington output.

brenzbmr@sb · Post by **brenzbmr@sb** » Fri Jan 11, 2013 10:01 pm

hey guys just got back from CES today, i did go check out PG and i must say the new TI amps look really nice.

i didnt get a chance to listen to the car but i did bother jorge alittle bit. product looks and feels high quality even to the entry level gear.

good job pg.

Kirghiz · Post by **Kirghiz** » Sat Jan 12, 2013 11:10 pm

http://www.ceoutlook.com/2013/01/10/pho ... ries-amps/

http://www.ceoutlook.com/2013/01/07/pho ... tion-amps/

That's the biggest news out of the show, along with the Bluetooth compatible amp mentioned in the other thread.

Post by **Eric D** » Tue Mar 12, 2013 5:39 am

What rock have I been living under? It took me 2 months to discover this thread and realize PG has even more fun in store for us this year.

These new amps look to be a great step in the right direction. Very small size with plenty of power. So long as they still sound as good as the other PG lines, these could be excellent choices for many people.

Post by **ttocs** » Tue Mar 12, 2013 9:21 am

funny enough I just saw that the company that makes my air-ride came out with a smart phone app for their systems. Thought I would have seen it but....

Rexarmy · Post by **Rexarmy** » Mon Apr 08, 2013 5:11 pm

dvnt88 wrote:
MW3 wrote:No additions to the Elite speaker line, maybe next year.

Morgan - Do you happen to know the MSRP / MAP on the new TI amps and availability to local dealers????

I know these are new but it would be nice the have an idea how many pennies I have to save?

Post by **ttocs** » Mon Apr 08, 2013 5:15 pm

Rex mang where you been? The 430 runnin yet? Mine is still under construction and I now upgraded to the Elite amps...

Rexarmy · Post by **Rexarmy** » Mon Apr 08, 2013 5:56 pm

It is running in in a friends car for now but I will be using it soon. I have been working on my car.

Post by **ttocs** » Mon Apr 08, 2013 6:23 pm

and not sharing any pics?! Shame shame....