Nakamichi 100 DAC
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
Nakamichi 100 DAC
I am new here,
below was my setup
nakamichi 100dac
Milbert TC 4R tube preamp
milbert BaM 235 class a tube amp
Phoenix Gold xenon x1200.1
Kicker solobaric S15D
Dynadio tweeter
custom make 5" mid range
custom make 8" mid bass
kicker pkd1 1/0 gauge
QED speaker cable
Monster 401 interconnect
monster 402 subwoofer interconnect
monster 100 series subwoofer speaker cable
now I need a HU with coaxial digital output to link with my nakamichi dac100, any Hu to intro to me? thanks.
below was my setup
nakamichi 100dac
Milbert TC 4R tube preamp
milbert BaM 235 class a tube amp
Phoenix Gold xenon x1200.1
Kicker solobaric S15D
Dynadio tweeter
custom make 5" mid range
custom make 8" mid bass
kicker pkd1 1/0 gauge
QED speaker cable
Monster 401 interconnect
monster 402 subwoofer interconnect
monster 100 series subwoofer speaker cable
now I need a HU with coaxial digital output to link with my nakamichi dac100, any Hu to intro to me? thanks.
nak mb100/cd700, denon dct-1, there's loads but these were the 1st that came to mind..
Ti1 headunit (unique)
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
Thanks, I found CD700 before, I know this HU had coaxial digital output, but if not mistaken, this HU got a lot of problem.......so I not going to use this HU.marko wrote:nak mb100/cd700, denon dct-1, there's loads but these were the 1st that came to mind..
nakamichi MB 100, yes this is one of my candidate HU.
denon dct-1 if not mistaken it was only the coaxial digital in but not coaxial digital out, am i right?
thanks for your suggestion, I am now finding the HU to complete my "analog SPL" dreamset, so any other HU?
the dct-"z"1 was coax in only but the recent dct-1 has both, this is why i'm also considering it as my next headunit to link up to my zapco da-ii dac..
Ti1 headunit (unique)
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
Oh.... I see, you also playing around with the DAC, I am new in In car entertainment, denon dct-1 ok, I will try to find it out, thanks, but I believe that the price will be quite expensive.....marko wrote:the dct-"z"1 was coax in only but the recent dct-1 has both, this is why i'm also considering it as my next headunit to link up to my zapco da-ii dac..
Thanks for your help, Can I share the picture of my car here?
yes, pics always welcome here!!
Ti1 headunit (unique)
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
As I check in the web, Denon DCT-1 seem like is using toslink "optical" digital output, but not the "coaxial" digital output. I will check to confirm.marko wrote:yes, pics always welcome here!!
My original door panel
My 3 way speaker enclosure to become my door panel.
Cutting all the unnecessary part from my door, to fit my 3 way enclosure.
3 way enclosure that make by wood
i like that!! at last someone doing a proper door build
Ti1 headunit (unique)
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
Ya I like it too, My power window are not functioning now, cause wan to fit this enclosure into the door panel, I had to remove my power window bracket in order to fit this enlosure into my door panel.marko wrote:i like that!! at last someone doing a proper door build
Actually the enclosure done, just I got no time to capture the picture, once I capture will share with you...
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
once you listen to the sound produce by the wood enclosure, you will never think about the fiberglassStryker wrote:whoa!!!!! that unit is prolly one heavy $%#*& to close. Fiberglass might have been a better choice. Why would you sacrifice fresh air intake in favor of a door enclosure??? ie not being able to use your window.
the sound is amazing....
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
Wow! I love that door enclosure, and the fact that all of the drivers are on the same plane. Great job.
XS2300, XS2500, XS2300, X200.4, X100.2, Ti21000.4, Roadster 66
I'm gonna become a civil engineer. I'm gonna design septic tanks for playgrounds. Little kids can take shits! You idiot, what the hell do you do?
I'm gonna become a civil engineer. I'm gonna design septic tanks for playgrounds. Little kids can take shits! You idiot, what the hell do you do?
-
- Posts: 12
- Joined: Wed Jul 29, 2009 6:23 pm
ya, that's why I create this enclosure. I got some reason to create this enclosure.dwnrodeo wrote:Wow! I love that door enclosure, and the fact that all of the drivers are on the same plane. Great job.
First, cause of the staging, I had try several time to get the staging by using the "normal install",
1. tweeter located in pillar, mid bass located in door panel.
2. tweeter located in kick panel (cannot cause this was right hand drive, unable to install the tweeter in this case)
by using the "normal" installation as mention above, found that the low frequency always makes an error, the low frequency unable to produce complete, so what I heard is the sound very "bright and thin sometime will got some noise". Ya this can be solve by using the function deck, with the 31 band EQ. But the digital signal that has been "modified" by the EQ, normally the sound not natural and pure.
Imaging, with the "normal" installation. Found that the imaging was not clear, then this issued will be resolve by using the function deck with time alignment, active crossover, let the HU to cross the frequency and let them can be independently having different time alignment. Ya this will provide the center imaging nicely, but when you listen to the quality of the sound, the sound was not natural.
In order to solve this 2 issued as mention above, for imaging part, I will try to make an angle for my driver, 3 driver was directed to same position, and in same plane, the distance between the driver was not more than the "speaker golden rules", the cubitfeet inside for the driver also try to apply it with "piston efficiency theory". I had try the sound, the driver that I using need certain distance to let the sound "reach" completely. So after install, I got the staging now and also the imaging, but one thing the imaging still not very accurate, I will solve this by applying the preamp, left right independent gain adjustment....
I am new in In Car Entertainment, I like to experiment, prove, try and learn.
I try to apply the fiber for speaker enclosure before, but the sound not as nice as the wood enclosure, mayb I am not skillful, but I am happy and enjoy with the music produce by my speaker enclosure now, thanks.