cecil or doc? anybody? GGGGRRRRRRRRR ROUTE66
- twisted
- Fordtough's Boyfriend
- Posts: 2542
- Joined: Wed Dec 06, 2006 3:26 pm
- Location: the vast unknown
cecil or doc? anybody? GGGGRRRRRRRRR ROUTE66
well, i went out tonite to install the route66 amp into my burb to hear the beautiful reproduction of my favorite cd's and low and behold the rh front channel has no output and the m25 side powers up but has no output
here are some pics of the inside if anybody notices anything out of the ordinary
m25 side
m44 side
here are some pics of the inside if anybody notices anything out of the ordinary
m25 side
m44 side
- twisted
- Fordtough's Boyfriend
- Posts: 2542
- Joined: Wed Dec 06, 2006 3:26 pm
- Location: the vast unknown
no line driver (i dont want to feed more than 2 volts cause i was told these m class amps can be damaged by that)
and rca's are just front and rear i hooked them back up to the orion amp and all channels play like they should
i have had the WORST LUCK with m class amps latley
and rca's are just front and rear i hooked them back up to the orion amp and all channels play like they should
i have had the WORST LUCK with m class amps latley
Last edited by twisted on Tue May 22, 2007 5:40 pm, edited 1 time in total.
Maybe the previous owner modded the amp. There seems to be several different ways
ftp://208.187.38.55/Phoenix_Gold/Manual ... 66_Sub.pdf
Do you have the 2 RCA's "y"ed somewhere? In other words, how do you have the 4 channels into the 6 channel inputs for the amp connected?
Also, a line driver will do no damage, will increase your total output and save the gain. I've had a line driver on my M series amps for 12+years. Same amps, same line driver.
Edit: I just noticed that the Route 66 has only 4 channel inputs. For some reason I thought it had 6.
ftp://208.187.38.55/Phoenix_Gold/Manual ... 66_Sub.pdf
Do you have the 2 RCA's "y"ed somewhere? In other words, how do you have the 4 channels into the 6 channel inputs for the amp connected?
Also, a line driver will do no damage, will increase your total output and save the gain. I've had a line driver on my M series amps for 12+years. Same amps, same line driver.
Edit: I just noticed that the Route 66 has only 4 channel inputs. For some reason I thought it had 6.
I see nothing wrong with the amp boards in as much as your photo's show. I think the two mode selector switches are not set correctly. Have you tried changing those setup switches.
Those mode selectors can be set wrong and you get no sound out of you M25 section.
I see what looks like a set of signal wires underneath the boards, as the M25 section has no front end electronics its signal must come from the M44 section, and those selector switches.
Try those and get back to me, you have my mail and phone.... C
Those mode selectors can be set wrong and you get no sound out of you M25 section.
I see what looks like a set of signal wires underneath the boards, as the M25 section has no front end electronics its signal must come from the M44 section, and those selector switches.
Try those and get back to me, you have my mail and phone.... C
twisted wrote:are the mode selector switches the orange knob lookin switches with a phillips head on them????
The selectors are those long silver looking box's with a single aluminum shaft sticking thru the end plate cover, there are three, you can't miss them the have a straight blade slot in the end of the shaft for screwdriver adjustment
These set your inputs and thus your outputs of each channel... C
- mr tibbs
- Forum Goatee
- Posts: 3895
- Joined: Sun Dec 17, 2006 3:03 pm
- Location: The land of morons, I mean mormons.:(
You said "shaft"!!!1moreamp wrote:twisted wrote:are the mode selector switches the orange knob lookin switches with a phillips head on them????
The selectors are those long silver looking box's with a single aluminum shaft sticking thru the end plate cover, there are three, you can't miss them the have a straight blade slot in the end of the shaft for screwdriver adjustment
These set your inputs and thus your outputs of each channel... C
Allrighty, I'm done, sorry for the threadjack mang. I'm out!!
that's how they are, they take the signal from the m44 section. pita if you wanna go 3way active as you have to modify the internal wiringshaheen wrote:I see the problem, ur M25 section has no RCA's , u need input to get output
Ti1 headunit (unique)
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!
Outlaw in crate.
2x original shrouded ms2250's.
Route 66 in box + custom m100 to match.
Roadster 66 in flight case
Octane LE in box.
Reactor #186 in flight case.
Reactor EQ232
Ti400.2 AL
AX204A + EQ232 + ZPX2 + TBA set
ZCS6 component set
Tantrum+Titanium bass cubes
Ti12d Elite sub
DD5 + DD10 + 6 Ti blocks!