And So It Begins.........Again...
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
And So It Begins.........Again...
Well my Phriends, I promised my two XS's+Cap to my buddy as payment for painting my house & figured I would temporarily put some gear in until I started my next build. Well after a few days I decided I'd rather not have such nice gear riding around unbolted in a rather dismal manner. So, I figure why not start a huge expansive project because I have no time to do so!
The wife just ordered a Shuriken BT60 for me (hope that will suffice), I just ordered 20' of hyperflex 0 gauge power+4' of 0 gauge gnd wire. I'll be putting the following into the subie:
Reactor, Ti1200.1, DD10, Ti BassCUBE, & possibly TLD66.
I'll keep using my Memphis comps & 3-ways for now & add my EliteD 12'' + a Clarion 10''(for mid bass)
I am thinking of using a spray sound deadener on the entire back as Dynamat is not within my budget. I have a few roll of Dead Liner but am saving those for the future 4Runner install
The wife just ordered a Shuriken BT60 for me (hope that will suffice), I just ordered 20' of hyperflex 0 gauge power+4' of 0 gauge gnd wire. I'll be putting the following into the subie:
Reactor, Ti1200.1, DD10, Ti BassCUBE, & possibly TLD66.
I'll keep using my Memphis comps & 3-ways for now & add my EliteD 12'' + a Clarion 10''(for mid bass)
I am thinking of using a spray sound deadener on the entire back as Dynamat is not within my budget. I have a few roll of Dead Liner but am saving those for the future 4Runner install
- Attachments
-
- DSC_0594.JPG (136.1 KiB) Viewed 13121 times
-
- Black is hard to keep clean...
- DSC_0552.JPG (140.41 KiB) Viewed 13122 times
-
- So long, it's been nice!
- DSC_0555.JPG (157.53 KiB) Viewed 13122 times
-
- DSC_0558.JPG (144.3 KiB) Viewed 13122 times
-
- Reactor sounded great but deserves better...
- DSC_0574.JPG (135.89 KiB) Viewed 13122 times
-
- DSC_0592.JPG (144.38 KiB) Viewed 13122 times
-
- All gutted, cleaned, & starving fo gear!
- DSC_0593.JPG (147.21 KiB) Viewed 13122 times
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Just editted my post-not putting in the 500.4, no need...
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Got my 0g wire today, not bad as far as flexibility for the price (ebay) & got the back rattle canned with some sound deadening spray. I'll start on the side enclosures soon, I'm going to match they're color with the gray trim.
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
I hope you're installing them in stereo in the front, otherwise you are going to draw the soundstage to the back of the car and cause cancellations with the Elite. Not ideal.Wrennagade wrote:a Clarion 10''(for mid bass)
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Yeah, I'm holding off on the tens for now. I have the spare wheel well all taped off but wondering if the space will be to large for the EliteD 12 as I'll be utilizing all of it ...what do you guys think?
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
You'd have to install it inverted.
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Why? I
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
Mounting depth for a start I'd say, unless you're building upwards from the wheel well too.Wrennagade wrote:Why? I
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Here's my subwoofer enclosure design...
Glassing the spare tire well now...
Glassing the spare tire well now...
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
make a frame to go around the outside of the glass and then you have the option of flush-mounting the sub from the back for a smoother look. Just make the entire top removable.
what else can I say I am a grumpy asshole most of the time.
Re: And So It Begins.........Again...
Elite is going to need a double stack of 3/4 MDF or 1" at bare minimum! It's a fucking monster!
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
got some 1"ordered already. gonna brace the enclosure as well...
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Well the glassing is coming along nicely, since I'm practicing patience & not rushing through my install it's going to take some time. I added braces to reinforce the sides & will be squaring up the sides with some slats hopefully tomorrow to help the MDF top fit evenly.
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
as long as those dowels are I would have gone thicker or tried to stabalize the center of them with smaller pieces.
what else can I say I am a grumpy asshole most of the time.
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
I figure the enclosure being in the well will stabalize it overall, these are there to keep the fiberglass from bending out of shape while it is out of the car & being worked on. My other fiberglass box was bent out of shape some & didn't fit as molded when I put it into it's spot...had to pound the well in some & force it into place! Didn't want that happening again, the MDF & car should brace it pretty damn good.
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
do you mean you are going to add more layers outside of the car? It does look a little thin but I would get it as thick as you want it too be while its in the car. Each time you add a layer it can pull/shrink the existing shape.
what else can I say I am a grumpy asshole most of the time.
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
It's about 3 to 4 layers thick right now. I've used 1+1/2 mat packs, 1+2/3 cloths & almost an entire gallon of resin. I was thinking this should be thick enough, but it's only my 2nd attempt at fiberglassing so you think it should be thicker?
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
For a sub enclosure I'd say 3 to 4 layers is a good starting point. Mine is around ½" thick (including an ⅛" layer of coremat) and braced heavily. Maybe a bit OTT, but then so is the sub you're using (mine's for an IDmax 12).Wrennagade wrote:It's about 3 to 4 layers thick right now. I've used 1+1/2 mat packs, 1+2/3 cloths & almost an entire gallon of resin. I was thinking this should be thick enough, but it's only my 2nd attempt at fiberglassing so you think it should be thicker?
Full Album
Re: And So It Begins.........Again...
easy way to test it, stand on it...........
what else can I say I am a grumpy asshole most of the time.
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Hmm. Well I'll keep layering it up then...
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
I build mine to the point that I know I can stand on it and not have to worry about it. To build thicker layers this is where its better to use the kitty-hair style. just tear off handfulls and soak them, use a roller to get the air out of it.
what else can I say I am a grumpy asshole most of the time.
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
Kitty hair? where do I buy this?
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
- Wrennagade
- Posts: 491
- Joined: Sat Nov 13, 2010 6:57 pm
Re: And So It Begins.........Again...
I went & bought a5.3sq. ft. roll of pink fiber glass installation....Hope that's what kitty hair is...bought another gallon of reason too, man this is getting expensive!
Ti BASS Cube
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Ti Powercore 15
Ti DD10
Ti Fuseblock(Power)
1xTi500.4(Thanks Brian!)
1xTi1200.1
2xTi X-overs/1x Ti Tweets
1xReactor
1xTi 12EliteD
MS1000TA(Black)
Alpine 3339 EQ
Pioneer MVH P8300BT
Re: And So It Begins.........Again...
the stuff I am talking about is white, and random sized/placed strands that are cut and pressed into a sheet. its easy just to tear off a handfull at a time, put it where you want it and then saturate it with resin.
what else can I say I am a grumpy asshole most of the time.