Right now the only thing they are really selling is JL and Alpine. They stopped selling rockford stuff awhile back. When I asked if they were going to sell PG they said they were looking into it. I hate the Addison store so I mainly go to the Plano store where my friend Frank is the manager. Which b...

In Dallas about the only non hack shop left is Earmark Car Audio. They were the #1 PG dealer in Dallas for years even after Car Toys started selling PG. Earmarks Quality work kept them at the top.

I saw that you got a dealer in Mckinney Tx. Have you tried to talk to Earmark Car Audio they use to be a big seller of Phoenix Gold stuff. Infact they still have the old power display in their stores.

I'm also running 2 JL 12w6 and 2 TI 600.2 one sub per amp ported.

tetraag wrote:Mine came to Texas! Thanks guys, some of my buddies want to buy one!

Maybe I'll have mine when Iget off of work today. Other wise I guess I was to late.

Bought a Ti 400.2 off me. Excelent to deal with and quick with payment.

Hope you enjoy it

Thanks

Brian

THe W6's are dual 4ohm voice coils. Currently I'm running 2 ti 600.2 and 2 Jl 12W6 I have my subs wired 2ohm and then hooked to each and bridged. They are beating the crap out of my subs. I can start smelling the subs fast if I beat on them. But for normal every day use it's great. My next thing I'...

THe W6's are dual 4ohm voice coils. Currently I'm running 2 ti 600.2 and 2 Jl 12W6 I have my subs wired 2ohm and then hooked to each and bridged. They are beating the crap out of my subs. I can start smelling the subs fast if I beat on them. But for normal every day use it's great. My next thing I'm...

I have always heard that it is important to have matching batteries as well to match the charge/discharge cycle and minimize problems. If the voltage is remaining costant, are you sure the computer is not having an issue an either pulling timing out of it or adjusting in some other way? It sounds l...

Sorry for the confusion I have 2 wires comming from the alt. One goes the batt under the hood and one goes to the batt in the truck thru an isolator. Right now I have batt seperate the one under the hood for the truck and the one in the truck for the amps. The batt under the hood is a yellow top The...

Hmmm... I would measure the resistance of all your new grounding points to make sure there aren't any weak connections. You might even want to try a dielectric grease on them. Have you set your amplifier gains by multimeter or by ear? Perhaps coming from the JL 1000/1 you are expecting the same out...

My 0 awg wire goes from the alt to the top post on the batt. The side post is the factory wire and it goes to the fuse thing under the battery tray. Then I have a second 0 awg wire from the alt to a isolator to the battery in the truck. Also all grounds were replaced with 0 awg wire. I have a voltag...

Need some help and thoughts. When I crank my system and it starts hitting the low bass notes the engine idle falls and it almost kills the truck. It never did this with my old system. Here is a break down of the old system and the new sytem. I've asked around and no one seems to have an idea other t...

denim wrote:

walker01s10 wrote:Thumper is building my box for 2 xcon 12s

LOL yeah I'm like alittle kid I can't wait to get it. He built a freinds box for 2 JL 12w7 and hes running 2 Ti 1200.1 on them and it hammers. Thumper does prob some of the best box builds I have ever seen.

Thumper is building my box for 2 xcon 12s

I have a pretty good VM Radio is a Kenwood DNX7120 I have a TLD66 sitting there if I were to need it. Right now at a 60hz tone I get a reading of 34.62 and it sounds great and I know I'm not pushing the subs or the amps to hard because after playing alot of bass songs for about an hour the amps were...

Eric D wrote:25V RMS is ~150W x 2 into 4 ohms.
50V (25V + 25V) bridged is ~600W into 4 ohms.

There is nothing special about these numbers, this is what the amp is rated to do.

Ok but I'm not hooked up 4ohms bridged. Right now I'm hooked up 2ohms bridged. So would it still be the same.

I would set it for 25V RMS on each channel, or 50V RMS bridged, using a 60Hz tone. But how do you know nothing else in your system is clipping? If it is, then you would need to resolve that issue first. 50 vac really right now I got it at 31.6 and it sounds pretty good and the sub isn't getting pus...

Yes it's a dual 4ohm sub

Oh yes its all wired with 1awg from the alt to the batts to the fuse block then 4awg to the amp.

Now do the gain settings look right

Heres the products JL audio 12W6v2 dual 4ohm voice coils wired one way its 8ohm and the other way its 2 ohm. Amp Ti 600.2 My thought is to wire the sub in a 2 ohm state then hook it bridged to the 600.2 Then set the gain for one of two ways sqrt(600*2)=34.63 sqrt(500*2)=31.62 Now my concern is that ...

Well I'll be hooking them up today this way since no one else has responded and see what happens. And to try to be on the safe side I'm going to lower wattage alittle. sqrt(2*500)= 31.62 Now if anyone else could answer this question that would be great or have an idea of what I should do please tell...

I was kinda thinking the same thing wire the sub 2 ohm then bridged to the amp.

sqrt(600*2)= 34.64 volts

Need alittle help Woofer JL 12w6 dual 4ohm voice coils I can wire them 8 ohm or 2ohm Amp Ti 600.2 If I wire the sub 8 ohm then hook it bridge to the amp would that give me a 4 ohm load? Or should I wire the woofer 2 ohm then hook it bridged to the amp and if I did this what would the out put be?? 4 ...

mhyde71/matt

Thank you yeah my kenwood has a 7" screen. So it should fit is not I'll adjust it.

Thanks again

Where could I get that image you have on the screens? I would like load that into my radio.

Thanks