Thanks for reaching out! I am located in Bryan Texas, just outside of Houston. I knew there was not a lot of traffic left on the site but I still recognize several of the names from 10+ years ago when I frequented the site much more often. Glad that there are still some people sticking around. I'm w...

Is anyone on these boards available to do repairs? I have an elite .5 that is in protect mode. I disconnected all the power and speaker connections and then reconnected it and it will not come out of protect mode. It has been in my daily driver for the last 10 years and I've been really happy with i...

Thanks for the insight. I am in the process of reaching out to the dealer through this forum and email. Hopefully we can get something done.

Finally got around to adjusting the gain structure and it made no difference. It is not rca/eq related as they were unplugged. I'll try regrounding the amp/switching it out next. Currently it is grounded to the rear battery not chassis.

Lots of good stuff to check. I'll look at the ground switch in the dq-61. Woofer dog, can you send a pm with repair cost est? Just want to have a rough idea

I think the head unit and processor were ruled out when I disconnected the rca from the amp

Finally installed my elite 1600.5, dq-61 to my factory head unit and there s a constant low level hissing noise from my tweeters. Here are all the things I've done that resulted in no change turned radio off adjusted volume Moved cross overs rewired the offending tweeter outside the dash unplugged a...

http://www.phoenixgold.com/products/amplifiers/Elite/product.php?productID=80 gentlemen, if you read good , it states that the sub channel is 24db/oct.......... it is the F/R crossover that is 18 db/oct.......... I never realized there are two different xover slopes. Great eyes! I'll give it a shot...

Manual shows 18db slope minimum and I can eq out the upper range as well with the audio control dq-61

Does it have enough power to run on the sub channel?

1100w @ 1ohm
800w @ 2ohm
???w @ 8ohm

If not, I'll take brand/model suggestions for 2x12's iso in a 4th order bandpass

Me too! I just had a local college kid pull all my old equipment from my van. I gave him an xs2300 and a idq 12 v1 for his trouble. He was over the moon.

I have been looking at the ID Max as well as the Morel SC. they have very similar price points and although the Morel only has a single voice coil I think that the 800 W you would get at 2 ohms is more than enough to power that subwoofer. You could run the .5 down to one ohm on the ID Max for 1100 W...

Bought a NIB audiocontrol unit that was shipped fast, insured and arrived in perfect condition. Great communcation

Ok, searched a ton of old posts and found no quick answers...
25 ft of PG seems impossible to find so what kind of wire do people recommend? Knukoncepts seems popular on some other sites. I'm just looking for a suggestions from the PG crowd. No CCA just looking for OFC...

Neil

I have been looking at the same unit. I have also considered the bit 10 and the 6 to 8 by Mosconi. I like the other two for the digital interface and more EQ bands; however, the simplicity of the audio control is that you never have to worry about a laptop for software going out of date.

I will be getting a new daily driver this year and I am faced with the question of "Is it time to upgrade the stereo?" My current setup consists of the following Pioneer DEH P7600MP ZX 450 ZX 500 Morel Elate 6" separates up front MB Quart Reference 6"separates for rear fill Image...

ok 1800 makes it easy. at sonicelectronics you can get idmax 12v3d2 for as low as $265 shipped so thats only 530 spent. i would put a ms2125 on each idmax. that leaves you plenty for comps and getting the ms2125s recapped. I've never seen an IDMax12 that low. Can you showme where on the site? I wou...

Tried to go on their homepage today and saw an odd message...
http://www.imagedynamicsusa.com/Home_Page.html

time to pick up a few IDQ and ID Max subs now

Mine came to Texas! Thanks guys, some of my buddies want to buy one!

My dad is an M44, who's your daddy

Nice

Mando was great. He had the item packed & ready to go before we finished negotiating price. Immediate shipping & even cleaned it up like new. Love my new d-block.

waiting... and not patiently

what is cooking in the pg labs

pm sent

I'm in San Antonio... let me know.
1-1.5 hrs

if your balls are cut open... call an ambulance