thanks for the replies, but this thread is dead since there's no way I can get 2 sealed 12's. Please see new thread.

Previously had 2 12 RSDs sealed with RSD1200.1. LOVED the sound. I've since changed cars to a hardtop convertible SLK55 and found I couldn't fit 2 12s. I'm planning: 1. PLANET AUDIO RXD2400 or HIFONICS XXVCOLOSSUS 3200 WATT 2. RE Audio XXX 12" I'm not looking for advice on SPL or SQL. Just your...

I have two 1200.1s on 1 15t" and it POUNDS. today i droped the ohm load n the rsd"s to 1 ohm to see if they could push at 1 ohm. sadly something happened to my 5 farad cap that i use as my amps distribution block and i didnt get to test em. Not to high jack this thread but has anyone used...

at 4ohms the colussus will do 600w x 2.

thank you for the responses. maybe i can run the 2 rsdc12's off the rsd1200.1 for now, see how it goes...

Linh

These seem adequate for 2 RSDC124's in sealed enclosures built to spec? Or would an rsd1200.1 be adequate? I've currently got a rsd12 sealed to spec with a rsd1200.1. the amps drive the sub to max excursion easily, but I've read that the rsdc is another beast altogether and i'll need more juice. I''...

Bfowler wrote:so what are you doing with the old one?

They've asked me to send it back

Just got an email from the ebay seller thecablesupply. They're shipping me a new one

Power is registering 12+? Ground is registering 12-? Remote is registering 12+? no case lights on the SLD44? I've called PG tech but they told me to just unplug everything and let it "reset." I've waited an hour but still no go... ^^^Was that Phil or Matt? power and ground both 13+ with e...

Power is registering 12+? Ground is registering 12-? Remote is registering 12+? no case lights on the SLD44? I've called PG tech but they told me to just unplug everything and let it "reset." I've waited an hour but still no go... ^^^Was that Phil or Matt? it was Matt. I called back and M...

Based on a few recommendations from fellow forum members, I purchased this line driver from ebay from thecablesupply. I finally got around to installing it, but can't get it to power on. I've checked the power and ground wires with a volt meter and it reads 13.7v with the engine running. The remote ...

thanks for the replies. Everything you guys said makes sense. I'm definitely going back to 1 rsd12, because 2 of them were taking up my entire trunk. I guess if I ever get a better amp I can put the 2nd 12 back in.

my guess would be less wave cancellation

Wow interesting. So you're saying the amp pushes 1000watts at 1 or 2 ohms? If thats the case, I'll probably just remove one of the rsd12's to regain some trunk space because I don't think I'm gaining THAT much more spl by splitting 1000w among 2 of them.

I know it's not recommended, but I've been running 2 rsd12d's at 1 ohm. I'm curious as to how much rms power this amp is pushing at 1 ohm? I've emailed PG techs but they wouldn't give me a definite answer.

Thanks.

gentlejax2 wrote:I got my 6 channel PG line driver from Cable supply...no problems...good deal....new in box...

I just ordered from the same vendor

AVICJR wrote:I just ordered one from egay and it took 3 days to get it. Not bad. Company's name is "The Cable Supply" also "RHC Trading". Give them a shot. 100 % feedback which is a rarity nowadays.

thanks for the headsup!!

This is getting weird, called 2 local car audio shops and none of them carry line drivers....

Guess I'll just have to order and wait

Hmm I just swamped out the x400.1 for the r15.0.1 and output is actually LESS, much less, even with gain at max. I guess a line driver is a must. I called 3 bestbuys and 2 circuitcity's cause I didn't want to order online and wait, unfortunately none of their install guys have ever heard of a line d...

The RF unit does come with a level adjustment, I have it at max, still doesn't do much. I guess at this point I'm looking at a line driver, or maybe a combo like the SLD44.

It was not me selling the MQ, you were harassing someone else

Thanks for the welcome. I'm a noobie with this audio stuff and decided to do my own install after reading a couple DIY articles... I've recently installed an x400.1 with an rsd12d in a sealed box. The car came with touchscreen NAV with the HU built into it so I didn't want to take it apart. Instead,...

Will I need one? I'm running the stock H/U from a Lexus IS350 and have no idea how much volts it puts out...