so a bridged 200.4 would give you 400W RMS into 2 channels . . so if I give them 270W RMS a side off a rainbow amp I should be ok? . . .
Cheers
Matt

Evening all, Can someone please confirm to me, the RMS power PER SIDE of the Ti 6 components? The manual states power handling at 300W RMS, but I guess this is total? It shows the recommended amp as a 600.2 connected to the crossover, and this does 150W RMS per channel at 4 ohms, so am I correct? Th...

ah OK. I didn't know if it was frowned upon to have the components running off the same power cable as the sub, but I suppose at the end of the day, what ever cable it runs down, its all being fed from the same source.
Thanks again. more shopping to do!!

excellent, yet more questions answered!! Thanks for the quick response. There seems to be only 2 online retailers of the RSD subs here, one states dual voice coils, but they dont call it the RSD12d. Going to have to hunt around for it! Thanks, I'll no doubt be along with more questions on setup shor...

Hey all, The current situation is: Ti6's, power by Ti600.2 or Xenon 200.2. Xenon 600.1 Powering an RSD sub. I think I am going to go for the 12", as you all seem to rate it better, and also because the required 0.5 Cu. Ft. for the RSD10 is impossibly tiny!! So I have a new question. or two. Rea...

bad ones!! I had a longmill a long time ago, and recently an in-phase, which was an inferior make, though it served me well. I dont have bass high in my system, but I decided in my next purchase I fancied something tighter and punchier. I'm going to have a good long look at the rear this weekend and...

yeah thanks for all your advice. It's definately between the rsd10 or 12. I want minimal space, but is there a huge step of difference between 12 and 10? I've always been a 15" guy so i'm in new territory!! I plan on knocking a couple of sub templates up and testing them in the boot. Would the ...

sorry to double post. Xenon 600.1 Purchased!!! Just out of curiosity, would that also power RSD12?? The RSD10 enclosure is going to be tiny!! I plan on fitting it into the side of the boot, near the wheel arch in a fibreglass enclosure. 0.5 Cu Ft If I'm correct, any specific considerations regarding...

excellent! Thank you ever so much for your advice. So once more to clarify:

Ti6 Comps - Xenon 200.2, will provide 200W RMS per channel, this will be 4ohm?

RSD10 - Xenon 600.1, will provide 600W RMS, is this safe? Depending on how powerful the RSD10 is, I might upgrade to 2.

Thanks again

I'm just looking at amps available, I'm struggling to get the xenon's over here, but new, I can get a 200.2, 400.1, and 600.1. so would I be best with a 200.2 for the comps, and which would you say for the sub out of 400 / 600?? Also, if the amps for comps and sub are going in the rear, would I be b...

you say the 200.4 would run my whole setup, is that including my Ti Comps? Or would I be able to just use a 200.2 for the sub?
Cheers

Right, after hearing all your good words, I think the RSD10 is the boy. Unfortunately in the UK as said, no chance of an RSD10c. So next question, what amp would you use to power the beast? was looking at the Ti's but in the UK they seem overpriced, any of the xenon range ideal? Or any other brand a...

yeah 15" is too big. I'm after a nice small install this time. I need all your help yet again. The more I look into it all the more I am at a loss, I've been out of the game too long!! I've started looking at the JL 10W7, but the ohm situation is beginning to confuse me, with my comps too. For ...

Competition? Haven't seen those, I'll give them a look in, it never seems to end!! My main concern is space in this install, so I'll measure up and see which is best size wise, is there a competition 10" too?
Cheers
Matt

right, so the best setup will be, 600.2 to the fronts, RSD12 / 10 and Ti800.1 to the rear. Just to confirm, the 600.2 wouldn't be overpowerful for the front speakers would it?
Thanks again guys,
Matt

the kenwood is a KAC-PS621. I had it bridged, running 150W RMS x 2 @ 4 ohms. My main ideas for change are that I have a new car, and more money to play with, so cash isn't a major concern. I'm running an Alpine IDA-X001, and what to get the TiEQ215 in there if I can find one. So I'm after a smallish...

Thanks for the quick reply, I'll give the RSD a look in. Whats your opinion on the 600.2? Am I right in thinking the comps can handle 300W RMS per side? I just fancy giving them more power if possible.

Hi all, I've only just found the forum, can't believe theres a dedicated PG board!! My first (definately not last) question is, what is the general opinion of the PG Xenon X10D2 10" Sub? I've been running a cheap 15" but want more SQ to match my Ti6's upfront. I like the look of the Xenon,...