What size do you reckon are the allen screws? Im trying to fine threaded inserts to fix the two plastc holes that have no thread?

I mean the Allen bolts that screw through the plate into plastic to give terminal support

Did it yesterday, it was easier than i thought, i realised with a dmm that the two bus bars have continuity between them lol so was pointless seperating them. One annoyance i have is that i realised the two screws on the power terminal have been over tightened by whoever buikt it! I was just checkin...

Right i think i'll give it a go tonight, so theres no need to undo the screws that hold the terminals to the plate? Just undo the 4 main bolts on each side?

Ok kewl, i will give it a shot soon. The power speaker terminal side is that plate that the terminal blocks screw into supported? I mean the terminal blocks i know they scre into the plate but is that plate actually supporting them? Just curious so i dont damage the amp if i tighten the power wiring...

If I just want to remove plexi, do I need to remove the screws of the terminals? Or just the 4 main body screws?

Ok kewl thanks for the advice, i'll be honest i rather not open it because i know i'll be paranoid about the screws if ive tightened them enough!

Thats a good question im not sure what the fs of the tweeters are

Oh and ive received my set i think stunning speakers from a build quality point of view cant wait for install

Same here! I got ur email wasnt sure how to reply

Yes same amp, your right about the adapt with voltage inputs but it also has another function which is to do with effiency i read up on the adapt again and i think it confirms what ive been seeing, if morgan could confirm

Ok kewl i'll check this out when i do my rewire, i'll be honest i have an issue with over tightening screws sometimes makes me nervous opening amps up lol need a torque screwdriver

I did more testing and have come to the conclusion that if either the front or rear left inputs are muted or see a low signal the amp stays on the low vvoltage rail but when either the front or rear left rca sees enough signal amp jumps into high voltage rail. I realised this when i remembered the a...

You have them active, what settings? Just as a base for me

Drock quick question, have you noticed how the bus bars in your pics look like they are touching? Mine also bend in a similar way but there is maybe 1-2mm gap, is it safe if they do touch?

Mine are on the way to me! Excited just thought id share

Cant wait to see these out there! Doubt i'll ever see one in uk tho.

Nice tidy build! Amps have dual power supply? They seem on axis i could mount them at that angle no problem will have to modify my apillars which currently run focal mirange and tweeters but i blew a midrange by accident so time break some fibre glass!

Good replies, my doors are deadened and sealed and i will run active (contrary to phoenix golds manual that basically says good luck trying to get them to sound as good active as they do passive) and run off ti21600.5 and 80prs. What position is best for tweeters? Im going to have to glass them into...

Ok yeh only downside ive heard is midbass is abit lacking, its either these or jbl ms62c

Hello im very interested in the components they look very good, anyone got experience with these? Ive read a few theeads on here but not any in depth ones thanks

Right ive summed it up been doing more testing, both front and rear channels if you just connect the right channels even with gain maxed you wont get more than 18-19volts and the clipping light is on. With just left channel connected the left channel gets upto 28volts plus and it clips at around 27 ...

Thanks for your info, yeh music makes sense dont listen to tones lol. I guess im paranoid, but because the clip light went of earlier when just the right channel was connected with the 1khz tone does that mean the right channel is actually clipping way before the left channel? The clip lightdoesnt f...

Ttocs, when using clip lights would you recommend doung that on music or tones?

It is a basic dmm, clipping lights are fine now it was with just the right rca connected it would show clipping earlier, that was the main point of the post dmm was just to give me a slight idea of where im at hence using the 40hz tone aswel as that i would expect to be ok on a meter designed for uk...