It sounds like your question is about a kenwood head unit, it has little to do with the amp. You should probably reach out to customer service wherever you bought the gear from. It's difficult to even understand your question...

I just ordered more parts yesterday. You can email me from the email link on the phorum here. It's the best way to get me quickly.

I was on vacation the last week of March through last week. I'll be back at the shop tomorrow.

I think that I've spoken with him via Facebook. At least someone contacted me asking for 4 remotes. The Email link for me on this phorum will email my shop address directly. It's the quickest way to reach me. After that either fb message or pm here. I just ordered more parts for remotes, so we are s...

Thanks Scott.

Rayman, pm me and I'll give you my email address or you should be able to use the email link from my profile.

... Echo... echo...

It's like a graveyard in here. I'm only posting this to see if the phorum is actually broken. I can't believe it's been 6 months since they're had been a post.

Later,
Jason

Yes, we still make them. PM and I'll reply much faster than a phorum message.

We still make them, but probably not fit much longer. I'm almost out of the specialty gain pot and I've not been able to source more.

I'll look next time I'm in the shop and remember. I'm not sure where it is, but I should still have the schematics I doodled. I'll do my best to remember to look for it

1N5400.

Any standard 3a rectifier with a >50V rating will work fine though. Their only job is to go short circuit when reverse polarity is applied. Kind of the opposite of a fuse to ensure the actual fuse does go open

If you tried to test the rectifiers in circuit they will always appear shorted. They cannot be tested in circuit as the transformer windings are directly across them. Out of hundred, I can count on one hand the number of PG amps I've had with shorted power supply rectifiers. It almost never happens ...

Yes, we still make them. We've been wading through some deep family shit over the past several months and have not been spending very much time online.

Tyrone, I sent you an email to the address that your friend in FB gave me.

Yes, I replied to you on diyaudio as well. We will get you set up. Thank you!

Looking for a replacement capacitor for my zx450 Its 2200uf 16v 105deg C measures approx 18mm x 35mm You need to replace all the stock Panasonic caps in the power supply, not just one. They leak and will eventually cause the amp to catch fire. Other than that, any general purpose low esr cap will w...

I still have bc knobs available. My daughter makes them now, but we still have boards and parts. I've been making them for something like 15 years now. I have lpl44's as well. Pm for details.

Later,
Jason

Iirc the polyswitch thermal sensors are designed to switch at 110° C. Obviously the interior of your car and amp should never be getting hot enough to boil water, sun or no sun. I expect that you still have something going on. In regards to your previous post, there are no transistors involved with ...

I've only worked on a few of the newer aamp PG products, but they are almost all common Korean designs with a bit nicer lipstick on them. You are going to have to figure out what is holding it in shutdown. Without a lot more information and without knowing your skill level or available tools, there ...

I've never seen a bad thermal sensor on any of these. It uses several ptc polyswitches as thermal sensors. I'd still bet on the trace under the rca connector. It's far more rare and unlikely, but it could be a failing comparator which is used to supervise and trigger the different fault conditions. ...

Was it working previously? Did you or someone else who is not a qualified tech disassemble and reassemble it? For that matter, tech or not, did anyone unfamiliar with these disassemble and reassemble it? If it went into thermal after being opened and then then reassembled, it's almost certainly a br...

I've not done any extensive research to determine if there are other factors, but literally thousands of hardware items and fasteners are nickel plated. Pretty much any screw you purchase that is bright and shiny silver, but still magnetic, is a nickel plated fastener. As far as I know, there is no ...

It's a 12v zener diode.

I'm sorry for the delay, I thought I answered this when you first asked, but I must not have submitted the reply. I've never seen a tantrum with anything but irf540's. I'm not sure where you found the other info but I've repaired dozens of tantrums, they all use Irf540 outputs. First of all, there i...

Have you ready the manual for it find here: https://download.phoenixphorum.com/Manuals/Amplifiers/Titanium/Ti800_1Manual.pdf the crossover on this amp is pretty straight forward but some of the multi channel ti amps are extremely complex. The top scale on the rotary switch is supposed to be the amps...

You will be very happy with it. Enjoy it and then pass it on to your kids. Build your own little phoenix phamily!

Overload led for a few seconds and then green led is normal startup behavior. The o/l led is lit while the poweramp is muted during power up. This is to keep any pops or thumps from hitting the speakers. The amp can easily overload a small DC power supply. You can run a more stout supply and either ...

Yeah, they are already charging sales tax on stuff whether it's new, used, or otherwise and then they want to get income tax too. We've given this ridiculous government way to much power. I'm not sure whom the taxes are helping, but it's not me. Most middle class Americans already have about a 38% t...