yup..i dind't get the 600.1

but a while back i got the300.4 for 108...what a steal...

you guys missed the amazing amazon sale on these a while backk

i got the 300.4 for $108 SHIPPED!!!!

you're right ttocs...but won't that tamper with my 300.4? right now im sending 4 channels into that...and bridging the 4 channels into 2. and sending that to the front if i were to run my rears off deck power...and fade the back...wouldn't that lower the power/output send to the 300.4 as well and th...

So If i were to remove the speakers from the rear, would there be much to gain since the bass from the trunk now has a path to enter the cabin (the holes where the speakers were) can anyone hear/feel difference? If i were to run the coaxials, off deck power, with ripping out the tweeter, how exactly...

setup: Deck: ALpine cda 9856 Amp: Jl 500/1, Phoenix Gold RSD 300.4 Front: Phoenix Gold RSD65cs (component) Rear: Phoenix Gold RSD65 (coaxial) Sub: Phoenix Gold RSD12D Car: Camry 2004 Currently I have only the front speakers hooked up (although both front/rears are mounted). I have the 300.4 bridged ...

i actually followed this tutorial right here, http://mobile.jlaudio.com/support_pages.php?page_id=143 which gives voltages for the amps at different loads, an what test tones to use. i've heard numerous poeple tell me about 50hz and using 1khz as well, and it was only right now did i learn anything ...

First and foremost... in North America, unless you have a True RMS voltmeter, you absolutely must use a 60Hz test tone, otherwise you will not get a proper voltage reading. JL Amp... since it makes the same power from 1.5-4 ohms, you have to calculate it as if it was a 4 ohm load. So... sqrt(500*4)...

Setup: Jl 500/1 (crossed at 80hz 12db, eq off, bass boost off) w/ Phoenix GOLD RSD12D (wired at 2ohm) Phoenix GOld RSD 300.4 Crossed at "approximately" 60-70hz Boost off. HP Selected. w/ Phoenix Gold RSD65c's (amp is bridged) HU: Alpine CDA 9856 (all eq off, bass 0, trebble 0, volume at 25...

i prefer sealed...for SQ reasons

for SEALED boxes..whats the optimal setting for SQL?

what kind of car are you running this in? hummer:? lol

Currently I have the pg rsd12d w/ jl 500/1 amp as well as pg rsd 300.4 pg rsd65cs and pg rsd65....nothing is installed yet except the rsd12d and jl500/1 but from just reading this forum...how everyone is going crazy over the rsdc...shit...should i just get one before its gone? im satisfied with rsd....

lol...stock speakers better then rsd?

hey guys, thanks for sharing all the information so far. very informative. now a couple of questions. For the rear speakers...is there anything I can do (besides grill) to protect them from the sun? The grills that come with camry's have a tendency to crack with a lot of sun exposure, so i feel like...

ok cool, thanks for the great tips so far guys! Last question....well for now hehe... I'm running the 300.4, and gonna be using it for both front and rear. Do i need to rewire the speakers, or can i use the factory speaker wires? I hear lots of people yes, you need it...while others say you won't no...

hey all so i got my PG AMP Components Coaxials and now waiting for my amp wires to come in. I need to order speaker adapters next has anyone had experience with the material "PVC" ?? http://cgi.ebay.com/ebaymotors/6x9-Speaker-Adapters-Toyota-Camry-03-09-Rear_W0QQcmdZViewItemQQ_trkparmsZQ7c...

yes...but dont get the knu klm 8awg kit for that amp. it uses copper clad aluminum which will put it right at the edge of that amps current draw. buy the kolossus flex in bulk or go with the klm 4awg kit, or komplete 8awg kit so whats the difference between komplete 8awg and komplete 4 channel amp ...

do i really need a distrubution block? Heres my setup Jl 500/1 with 4 gauge power/ground wire (knuconceptz kit) If i get a distrubution block i would need to get one that can accept bigger, thicker wire, ie 1 or 0 gauge, and then connect that to the distru block and output 1 to the 4 gauge for the j...

yes...but dont get the knu klm 8awg kit for that amp. it uses copper clad aluminum which will put it right at the edge of that amps current draw. buy the kolossus flex in bulk or go with the klm 4awg kit, or komplete 8awg kit so whats the difference between komplete 8awg and komplete 4 channel amp ...

ok cool looks like ill get another pack of knu then. is 8 gauge plenty?

what exactly is the difference between these 2 items (picture looks the same)

Complete 8 Gauge Amplifier Installation Kit
Item #: KOL-AK8


Complete 8 Gauge 4 Channel Amplifier Installation Kit
Item #: KOLAK84

hey,

So i ordered the 300.4

What amp kit (gauge) do you think i will need for this amp?

any particular brand of wires are good? I currently use knuconcepts in my car for the subwoofer

from reading this thread i might just pick up a rsd amp then...long live pg!!

hey what does everyone think of this amp?

Phoenix Gold RSD300.4

i'm thinking of getting this to power my components front and back

as spock would say, if he were to speak to PG

"Live long and prosper"

-Vinh

It looks like the person in question may have sold the amp already (boo)

So what other suggestions? I tried a quick google search for that amp, and most FS posts are years old...

Oh, and it doesn't have to be PG amp, it just has to be quality + under $200.


Thanks fellas,

-Vinh

Realistically, that amp has way more than enough power to kill those RSD comps....I have personally heard the ZX450 on the comps and it goes SUPER LOUD without clipping at all......the ZX amps have mega headroom, there is more to look at than just power ratings.....the ZX amp also has the built in ...