Being the owner of 2 ZPA 0.3 and 2 ZPA 0.5. I,m alittle biased. I,ve had the M series and the ZX.
Swaping from the ZX to the Zpa and the sound difference was a great improvement. Speakers came " alive" witha real depth to the sound.

So for me. Best I,ve every had.

I have been told to stop being a pu**y and put the full set in. Oh well here goes nothing, now where did i put that jigsaw.

Bigger plans for the doors may be needed then. Marko also said not above 1 khz.

So unless anyone has tried it back to plan A.

Is it possible to use the 9m driver as a midrange in a 2 way system using the TI Elite crossover.

The spec sheet on the 9m says a frequency response of between 40hz - 15khz.

Any ideas.??

Welcome along.

A M100 would be an ideal solution for you. Run the sub from that and use the M44 bridged to run your front end and if you want to keep the M25 use it for the rear. The M44 for the sub wont give you much over the M25.

How about a single Elite 12 running of the 2 x ZPA 0.5.

And the front end off the 2 x ZPA 0.3.

Comments on this.???

Also anyone run an elite ported.??

It would be much easier if they made the elites duel 2 ohm too.

what about a pair of cyclones IB? that would work well ran off the 0.3's and leave the 0.5's for the front end. Don't start me off, you cost me more money than the wife... :lol: :lol: Cyclones are harder to find and prbably cost more than the elites. Oh and i forgot to say. All this is going in a R...

Front end will be Ti 6 elites with Ti 9 midbass.

Kit list is in my sig.

Just trying to make my mind up on what subs to use. I would love a pair of elites, would a ZPA 0.5 on a pair be enough, 4 ohm final load.?

Now i know the ZPA 0.5 can run 2 ohm mono if you clip the resistors but will the amp suffer from doing this. Also is it possible to do the same to the 0.3. If so so what output would i be lloking at. I.m considering a pair of Ti elite subs that are duel 4 ohm. Just need to know if i can power them. ...

It will be gettng painted black to match everythng else before it goes in.

My little stash. All will be going into a Mitsi Evo6.

The M50 will be fine running our sub so nothing to worry about there. Good luck with your search for a M100, it will be worth it.

They are holding funds for 21 days now too. !!!!!!!!!

They expect you to post out and wait for either positive feedback or comfirmed delivery till they pay the seller.!!!

Ebay and paypal have been ********.

I won the item and paid. Then ebay / paypal have held funds for 21 days and the guy refunded money because of this.

If anyone knows him etc that would be great.

Is this anyone on here or do you know him.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 0314895978

1 of them is complete the other needs trimming. Might get it done 1 evening this week.
God knows when the rest will be done.

Belive it or not, I'm trying to keep the inside of the car looking as oem as possible. This is a pic of door builds with the 6 in them. http://i152.photobucket.com/albums/s181/masonsjeep/DSCF1498.jpg http://i152.photobucket.com/albums/s181/masonsjeep/DSCF1495.jpg Tweeters are low down on the A pilla...

Not a clue at the moment.
The car has Zx amps in at the mo. Its all coming out for a rebuild with the ZPA amps and a few more bits.

PGsta14me wrote:Would they do well even in an IB situation (with sound-deadening in doors)?

I don't want to change the doors hense the floor mounting.Same as this...
http://i3.photobucket.com/albums/y51/Haz1/100_0382.jpg

The Ti6 comps will be on the passive x-overs highpassed at 150hz
The lack of midbass was the reason for getting the T9m drivers. They will be mounted infront of the front seats in dedicated enclosures. hopefully this should do the trick.

I was thinking of using the MX2 for the subs for a while , so i can adjust the frequency till i get it right . I may lift the frequency on the T9m too.

Whats the cut off frequencys that people use for these.? Also how much power are you using. I've almost got all the kit i need and will be running the following.... Zpa 0.5 >>> Ti6 comps ..... 150 hz and above Zpa 0.5 >>> T9m ..... 40 hz to 150 hz Zpa 0.3 >>> Kicker XPL 15 ..... 80 hz and below Zpa ...

Very good comunication and great to deal with. Bought a MX2 from him and will definatley deal again.