Yea I felt pretty silly when I remembered lpl stood for low pass level. I had to laugh at myself in that one.

Just out of silly curiosity. The low pass on the amp is on right. I did this once using the low pass on my deck and had the amp crossover off

Got a tideq from him. Looks good shipped well. Recommended.

Going surfin'? That thing is huge.

Sounds like you have it down. If I remember right you can make 1 ch center and 1 sub on the bit one. You should be dialed.

Stoked the bit one is an amazing piece. I haven't installed a better processor yet. It can take a while to tune though but I love that part. I took half a day tuning one in a customers dodge and I played some Garth brooks live in it and I got a little chocked up. Felt like I was there with the crowd...

Yes it should work. It just doesn't seem like that would be 2 things you would want to control simultaneously. I hate going through the menus to turn my sub up and down. That's why I like the lpl. It's a quick turn the knob sub goes up and down. I wouldn't want to loose my mid bass as well. I'd do t...

After a bit of inter web combing it looks like they are the fan wires.

I've been looking at a 900.7 on the bay. He posted pics of the inside and there are red jumper wires on each side of the caps. Is this normal or has it been repaired? Thanks for the help.

http://pages.ebay.com/link/?nav=item.vi ... 1606975714

I'd start with the high end Kenwood double din screens with the 5.1 outputs for the front and go from there. I've done quite a few of those vans. I can give you way too much info if you want.

RayBuck wrote:What's going on in the back ground weaklink I see a grinder an a metal rack??

I'm an electrical contractor in the Oregon iron works marine dept. can't say much more. We built the new Portland Fire boats.

That's a nice blue-point roll cart you have there. Wanna see mine? Sorry had to do it. Love the blue snap on stuff.

Yes. Audison bit one. Dodge Charger. That is all.

My question would be what other locations do you have up front? If you can fit them the morel 3-way set sound amazing. A bit of coin though. I think my old shop is clearing them out. I can check for you if you want. Or the hertz hsk 163 3-way set like I have have a 6 that has huge mid bass output. B...

I could draw you out a simple relay limit switch setup if you want. Maybe even timers if you want. A dei 530t might work as well.

I remember the alpine pdx amps being stackable. Kind of a gimmick though.

Ok. So over volting is not the problem then. Still double check voltage at the amps just in case a power wire from the distro to the amp isn't coming loose. I would think the volt meter gets its reading before the voltage is split. Could maybe have a voice coil that is starting to short when it gets...

So without knowing which light was on when it was in protect might make this difficult. If it was thermal you might have the thermal sensor in the amp going bad. It sounds more likely it is a voltage issue. Check your voltages at the amp may be a weak ground or fuse. I had a voltage regulator go out...

Yep. Looks good otherwise though.

Got a powercore 15 the other day. Opened it up and the 2 screw terminal block is broke. Does anyone have an extra one of these? There is also a white wire coming out of the cap not hooked to anything. Where does it go? It's also missing 1 fine thread black screw and 2 coarse thread black screws. Any...

I thought it was pretty cool that the first production one ever made is still in this good of shape.

Trickyricky can make them. Did you use a new cord in the install? It needs to be a crossover cable if you did. Standard cord doesn't work. Welcome to the phorum hope this helps.

Got a bass cube from me. Smooth as always.

So I finally got a bit of free time and replaced all 8 resistors just to be safe. All channels work now. One thing left is now the front right channel is not affected by the crossover switch. It is fine in bypass but gets quieter in hp or lp and still full range. The front left acts proper on all th...

Yep. Came out clean. Even tried tracing paper just to be sure.