The Zxv2 and up will accept up to 6vrms What happens if i use a line driver and it gives the amp more voltage then the amp accepts? The signal will "clip" which sounds like raspy distortion. May damage your speakers, but seldom damages the amplifier. If you give an amp way too much input ...

knightrider358 wrote:The Zxv2 and up will accept up to 6vrms

What happens if i use a line driver and it gives the amp more voltage then the amp accepts?

I got both and the only difference i see are other newer caps and different printing on the board and outside, the plexi windows are darker on the titanium amps that i have seen.

Thats a nice clean M50, cool serial nr on it

Well don't forget that each channel has it's own gain adjuster. Are you saying that with both set to the same level they are not equal? It could be the phase is not set properly. Yup thats right with both set to max it shows 0,78 on left and 0,42 on the right the right pot is very loose and easy to...

Sounds good, how is the sound in the zpa compared to the zx600ti?. Maybe i will try and run the zpa on my components speakers they are 250watt rms in 4 ohm so i think it will sound good, my focal P25DB is 250watt rms but its dual coil is it 250wrms per coil or are they 250wrms together? The zx400ti ...

Not 100% sure but I'd bet 35-40 amps if it's cranked. I'm willing to bet that a 25-30 amp fuse could work. Hi thanks for answer, it is not the fuze size im worried about its more that im scared im going to use more ampere then my alternator is putting out. Im thinking of going with the zx400ti on m...

Not sure what this last question is... But as for the first, there are 2 sets of yellow pots that can be adjusted. One set does the phase, the other does DC offset. I've heard a couple of way to do the phase but I do t want to give you bad advise on how to do it so I'll leave that off. Once you set...

Im playing with the ide of using the zpa instead of the zx600ti for my focal dual coil subwoofer, how much amp does the zx600ti use compared to the zx600ti?

Well don't forget that each channel has it's own gain adjuster. Are you saying that with both set to the same level they are not equal? It could be the phase is not set properly. Yup thats right with both set to max it shows 0,78 on left and 0,42 on the right the right pot is very loose and easy to...

Im thinking about using the zpa0.3 instead of my zx600ti its going to run my Focal 10" dual coil subwoofer, i tested the zpa yesterday im going to change pots and the transistor with scuff in it but i just had to check if it works. It works fine now but there is different strenght in the output...

That looks pretty cool. I wouldn't use the amp boards ground to ground the lights. I'd run the wires out through the cooling vents on the side and connect the LEDs independently from the amp. Otherwise you are asking for noise. What about using red or orange glow for,the fan and then blue or white ...

Here it is with blue light in a clear fan and a strip inside the amplifier, im doing white inside + the three led white on one of my zx600.
Its hard taking picture with those blue led on it lights up better inside then the pictures shows.

I always try to get the soft wire because its easy to put in and look good, i see sound quest got 0/1 gauge cheap and it looks like its the soft type cables. Here is a link> http://www.ebay.com/itm/NEW-STINGER-SOUND-QUEST-0-AWG-GAUGE-COMPLETE-CAR-AMPLIFIER-INSTALLATION-KIT-0G-/181303786450?pt=LH_Def...

aquote="ttocs"]I have seen a couple led fans and it didn't look too bad.[/quote] I tried to find a clear led fan that is 0.19amp and have the same CFM & RPM as the original fan but I cant find one, I found a clear fan that is 0.18amp on ebay but I does not got the light i will try and ...

Im doing the same just finished the right side on my zx400, im using blue led but i was told by the seller i could cut the led strip it did not work only some of the leds light up on the right side so i will add a new and place it better. Where do you get Power for the led i put the + of the led in ...

Perhaps it has an voltage read out adjustable pot like my RMDs. If so adjust it to match your DMM. Two of the resistors on top gets really hot and the display got a black spot, i also testet the 3 feet led that shows what voltage it has is not working and there has been alot of heat. At this point ...

up

Im giving up on the amplifier Box i have made a mounting plate and im using the zx400.2 on the front Component speakers and the zx600ti on the subwoofer. I still have to see if i can fit the audio Control dqx under the floor i hope it fits under there, im going to fit the board inside the car and dr...

Did another deal with tricyricky this time i bought zx600ti,600titanium,tba1,lpl44 and some parts all packed bulletproof, he also added resistor that i did not know i needed he is a great guy to deal with i have learned alot about repairing amplifiers dealing with him.
Thank you for all your help

Thanks for your reply i have cleaned the pots and swiped them many times but i will try some more cleaner and test it again.
Finished the zx400ti today and it sounds great, it has some flashing on the Three leds when i swipe the crossover i will try to figure out what the problem is.

Mine shows damage by someone trying to fix it but missing the skill to do so, one of the pots are not in its house and one transistor has deep scuffs.

Nice soldering job. Looks like mine. You like those caps? Very similar to OEM. Nice LPL44 Ricky. Yes i like those caps i want it to look original, im putting the heatsink back on tonight i have to Paint the heatshields in the middle because there is some surface rust on them but i think it will loo...

Show a close up of that LPL44 I made you....looks better than factory, ooops sorry PG. The ones you make look much better then the old ones its just as better design, the knob looks and feel really good and you have great price on them i cant wait until i get my bass cube remote. Here are some Pict...

Well the post Office had alot for me today, here is some of it but i also got a 600titanium and zx600ti they are in my storage room and i will get them later i got enough removing the cap feet on the zpa. I also got the Audio Control DQX with the ddc remote the other day, the dqx need a new chip but...