what do ya mean "about to finish" lol? I am was beyond happy when I got the timing set and it started to sound ok. Was 3x as happy that when I figured out the new thermostat was bad and got it to stay cool by replacing it. Figuring out the temp enrichment to get it to start when its hot w...

Thanks for the feedback, I think ill have to do that to my friends neon, once I get it together.

Are you getting excited about finishing the car?

Sent from my SM-G960U using Tapatalk

I think you are onto something there, I wouldnt activate the system to bleed it, but thats just me. Heres a good article on bleeding ABS systems. http://www.brakeandfrontend.com/bleeding-abs-systems/

Sent from my SM-G960U using Tapatalk

Check your pms scott .

Sent from my SM-G960U using Tapatalk

No way!

Sent from my SM-G960U using Tapatalk

Thanks for the info!


Sent from my SM-G960U using Tapatalk

Happy birthday buddy! I figured you were having stomache issues because you got quiet. Pressure bleeders work magic if you have the correct adapter. I know on my car, i have to keep positive pressure or the abs accumulators will have air in them and you have to go to the dealer to have them bled.. w...

Hows the mustang coming

Sent from my SM-G960U using Tapatalk

Good news! Do you have a pressure bleeder? It was are a god send when I installed my Wilwood 6 pistons.

Sent from my SM-G960U using Tapatalk

Ok so start it without the accessories belt on and see if it cranks over. Hahaha tightening the belt too tight is a quick way to destroy an alternator

Sent from my SM-G960U using Tapatalk

after a LOT or trail and error I finally got it all running and idling and keeping cool today. I was taking it down the driveway carefully with the new rear end gears and new hp and killed it. Then the starter was really slow and for some reason blew the main power fuse on my power wire. After repl...

Get ahold of khamelion Koatings they do the amp decals

Sent from my SM-G960U using Tapatalk

If you navigate to the how to section of these forums, there is a very good tutorial on the repair process, and a few posts under the stickys on how to repair the through holes. If i recall correctly pg used a 4 layer board? I could be wrong there. But broken is VIAs generally bad if not repaired......

Id recap it before it sets itself on fire. I bought an M50 the other day that is in pretty good shape cosmetically. The PO said that nothing had been replaced and he didn't want to deal with fixing it. I hooked it up and it turned on fine. The problem comes when I adjust the gain up (past 30%) the a...

One of these guys has a parts list. Im not sure if its whitenoise or eric.

Sent from my SM-G960U using Tapatalk

Im pretty sure there are 2 sets to deal with both halves of the waveform. Pm jacamb2, ericd, ttocs they seem to know what they are talking about.

Sent from my SM-G960U using Tapatalk

Hello everybody for the moment i'm repairing a M44 amp. It has blown powersupply fets and other issues. There are 4 IRFZ44 fets with their gate resistors of 100 Ohm. If you look closely you can see that there are only 3 resistors of 100 Ohm the most left one measures 51 Ohm. Is this normal? (it loo...

Matt at Khamelion Koatings does an awesome job, he can either do the whole project for you, or like me, provide him with the artwork he prints it and you apply it. https://m.facebook.com/KhameleonKoatings[img]https://uploads.tapatalk-cdn.com/20180801/6af13e8cbc4e6397c20179234ade8621.jpg[/img] https:...

Thanks again for the reply, the place I took it to is very reputable. They even design and sell their own line of marine electronics. I have 100% confidence in them. Hopefully it won’t bite me in the ass. I just dropped the amp off a little while ago and he said wouldn’t be a problem, he tracked do...

ttocs wrote:so seriously now has anyone seen one yet?

Vaporware apparently


Sent from my SM-G960U using Tapatalk

ttocs wrote:so seriously now has anyone seen one yet?

I have not see one at all.

Sent from my SM-G960U using Tapatalk

ttocs wrote:yea its not like pg would waste a bunch of money on one amp that never functioned COUGH MPH-6300 COUGH COUGH

HAHAHA... It was just never finished is all.. hahahah.... Right?

Sent from my SM-G960U using Tapatalk

I never had an issue with the system while it was rolling, but for the first air these were completely aired out bags that were then just one valve switch away from 150 psi. I tapped the switch for a fraction of a second and thought something exploded. It didn't it was just tight for the first time...

No matter how fast you touch the switch to let a little bit of air into it for the first time it makes it make a "POP" noise and needless to say that is not the first noise you want to hear from them.... You could make a pwm control system for the valves so you can control the fill/dump s...

oh heck your right I completely forget every single one of them. I just had my head in other places and it never occurred to me to put them in. https://c2.staticflickr.com/2/1824/29441179838_3fa023e5aa_c.jpg I replaced the air bags this time with ridetech shockwaves that integrate the bag into the ...