xvr14 crossover questions

bogart · Post by **bogart** » Wed Sep 09, 2009 9:23 pm

ok guys...so do these crossovers draw 4 ohms or do they draw 2 ohms loads off the amp? I can't find the manual on here or info on it.....my intent is to run it off either the 2125 or the 2250 tri path so if it draws 4 ohms I would use the 2250 if it draws 2 ohm loads I will just use a 2125 and it'll do fine.

question 2....anyone know if non polarized electrolyte caps deteriorate as badly as the nippons on the ms and m amps? Is this thing going to be another rebuild new in the box project?

76Trans Am · Post by **76Trans Am** » Thu Sep 10, 2009 5:45 pm

XVR14 is set up for 4ohm subs. So it should be 4ohm load
XVR12 is for 2ohm subs.
Center channel is optional but I do not think the rear fill is..
It is needed to balance out the load.
The difference is the coil needed to crossover the upper end of the subs
I do not think these caps deteriorate like the ones in the amps.

GX3 · Post by **GX3** » Fri Sep 11, 2009 7:49 pm

You should just not use it and sell it to me

DO NOT USE MORE then 500 Peak power in bridged mode!!!!

GX3 · Post by **GX3** » Fri Sep 11, 2009 7:58 pm

XVR 2/4

XVR12/14 Hope this helps

bogart · Post by **bogart** » Sat Sep 12, 2009 10:40 am

thanks my friend!!!!! those are what I've been looking for. I just bought two nib xvr2's and I have a line on an xvr14....so I figure I'll run a 2125 to each side of the front stage with two comp sets and the re sx8s which are d4's...then I will use the xvr14 off of a 2250 and that will run the center the rears...and the gs redline overdrive 15 which are 8ohm drivers....hows that for old school

GX3 · Post by **GX3** » Sat Sep 12, 2009 10:45 am

carp ......please tell me your not the one i have been trying to out bid on the bay for the 14

bogart · Post by **bogart** » Sat Sep 12, 2009 10:50 am

I took it up too 63 and said fuck it...I can get a used one for 50

sorry to you for jacking your up...I've got another lined up so go for it

GX3 · Post by **GX3** » Sat Sep 12, 2009 10:53 am

can you pull your bid???????

bogart · Post by **bogart** » Sat Sep 12, 2009 10:56 am

I don't know....how do you do it and I will sure as shit try!!!!!

GX3 · Post by **GX3** » Sat Sep 12, 2009 10:57 am

bid retraction ........ let me look

bogart · Post by **bogart** » Sat Sep 12, 2009 10:59 am

I think I can only do it if I am the winning bidder...but I am not too sure. If you can figure it out let me know. I will be looking too

76Trans Am · Post by **76Trans Am** » Sat Sep 12, 2009 11:02 am

Be carefull with the XVR14 on the 2250. It is only rated for 250watts. RMS.

GX3 · Post by **GX3** » Sat Sep 12, 2009 11:06 am

here it is I have done it before with out any problems

http://offer.ebay.com/ws/eBayISAPI.dll?RetractBidShow

GX3 · Post by **GX3** » Sat Sep 12, 2009 11:07 am

select wrong amount

bogart · Post by **bogart** » Sat Sep 12, 2009 11:17 am

I just tried and it said that it has to be within on hour of the bid being made....It also says it can't be done within 12 hours of end of auction....sorry...I am going to keep trying other ways but I am not sure I can do it......

GX3 · Post by **GX3** » Sat Sep 12, 2009 11:19 am

That sucks ..... Thanks for trying ..... What's your highest

bogart · Post by **bogart** » Sat Sep 12, 2009 11:42 am

that was it....63 bucks....

GX3 · Post by **GX3** » Sat Sep 12, 2009 12:43 pm

$78 and I still didn't get it ;(

bogart · Post by **bogart** » Sat Sep 12, 2009 2:28 pm

that sucks dude...I figured it would go above 100 bucks really and he is an hours drive from me.......do you need one or just wanted a nib one....there are nib xvr2's on ebay for 29.99 right now....just bought two and he has a few left....

GX3 · Post by **GX3** » Sat Sep 12, 2009 4:08 pm

bogart wrote:that sucks dude...I figured it would go above 100 bucks really and he is an hours drive from me.......do you need one or just wanted a nib one....there are nib xvr2's on ebay for 29.99 right now....just bought two and he has a few left....

Just want it... I bought my 2 XVRs2 from the same guy a long time ago

Also have an XVR4 nib .................. I received a 2nd chance offer from the seller

think i should ??

bogart · Post by **bogart** » Sat Sep 12, 2009 4:12 pm

For 78 being new n the box...hell yes...worth it for collection for that

GX3 · Post by **GX3** » Sun Sep 13, 2009 10:31 am

working on a deal for a 2nd one he has to sell

bogart · Post by **bogart** » Sun Sep 13, 2009 10:34 am

HE has two? If you end up with both I want one ... I want one....

GX3 · Post by **GX3** » Sun Sep 13, 2009 10:35 am

Ill let you know as soon as i hear back from him.

bogart · Post by **bogart** » Sun Sep 13, 2009 10:37 am

sounds good to me....