Dimensions of MS 2125

Need help with your car stereo system? Have a technical question? Post here.
Post Reply
Lance_S
Posts: 121
Joined: Mon Apr 11, 2011 7:43 am

Dimensions of MS 2125

Post by Lance_S »

Size of the MS 2125? Pulled the owners manual but it didn't have the dimensions on it. Thanks.
todd217
Posts: 1127
Joined: Fri Apr 10, 2009 2:36 pm
Location: rantoul illinois

Re: Dimensions of MS 2125

Post by todd217 »

approx 17"L 11.5"W 2.5"H not counting the terminals and rca add about .75" for them.
Lance_S
Posts: 121
Joined: Mon Apr 11, 2011 7:43 am

Re: Dimensions of MS 2125

Post by Lance_S »

Thank you very much.
ttocs
the Floor Sweeping Hack with Golden Ears
Posts: 14797
Joined: Fri Dec 19, 2008 9:53 pm

Re: Dimensions of MS 2125

Post by ttocs »

funny I have been wondering this myself lately.
what else can I say I am a grumpy asshole most of the time.
User avatar
00goobs
Posts: 386
Joined: Sat Jul 03, 2010 7:59 am

Re: Dimensions of MS 2125

Post by 00goobs »

Lance_S wrote:Size of the MS 2125? Pulled the owners manual but it didn't have the dimensions on it. Thanks.
What are you planning? I have a 2D drawing in .dxf if you like...
Lance_S
Posts: 121
Joined: Mon Apr 11, 2011 7:43 am

Re: Dimensions of MS 2125

Post by Lance_S »

A single MS275 running tweets, and two MS 2125. One running mids (RX6 series massive audio) and one bridged running a single 12 Alumapro Alchemy MX12 in a sealed 4th order to manufacturers specs, all at 4 ohms. Active off a Alpine 9887. I cut out a template on the 2125's tonight to see how much room I have to work with. Crap, these things are bigger than I thought. I expected them to be close to the MS275 I have, I was wrong....by alot. I have to redo my install completely to accomodate. But I believe it will be worth it. Haven't received the amps yet (couple days)and all three amps need caps so I have my work cut out. I don't have the massives installed yet either so I have a ton of door treatment to do to the doors. They pound. Will be lucky if I have sound by the weekend. Mostly likely next week some time. Need to run larger hot line to my disto block (2 gauge). Need to up the ground from the bat to the chassis and the chassis to the alt. Need to put in a breaker for the hot side at the bat. Lot's to do. Just getting started.
Lance_S
Posts: 121
Joined: Mon Apr 11, 2011 7:43 am

Re: Dimensions of MS 2125

Post by Lance_S »

Anyone have a line on a good set of 90 degree RCA's? I need to keep the space to a minimum on these 2125. I may even consider look for 90 degree power and ground spades as well. Any ideas? Not looking to spend a fortune, did that already on 3 new amps.
ttocs
the Floor Sweeping Hack with Golden Ears
Posts: 14797
Joined: Fri Dec 19, 2008 9:53 pm

Re: Dimensions of MS 2125

Post by ttocs »

how many do you need? Do you want just the rca ends or the adaptors that the standard rcas plug into?
what else can I say I am a grumpy asshole most of the time.
Lance_S
Posts: 121
Joined: Mon Apr 11, 2011 7:43 am

Re: Dimensions of MS 2125

Post by Lance_S »

90 degree adapters, so I can plug my male end RCA's into them. Just trying to save some space, it's going to be relatively tight. I would need 6 of them.
ttocs
the Floor Sweeping Hack with Golden Ears
Posts: 14797
Joined: Fri Dec 19, 2008 9:53 pm

Re: Dimensions of MS 2125

Post by ttocs »

I got what you need then, I can send a pic if you give me your email.
what else can I say I am a grumpy asshole most of the time.
Lance_S
Posts: 121
Joined: Mon Apr 11, 2011 7:43 am

Re: Dimensions of MS 2125

Post by Lance_S »

pm'd
Post Reply