PG RSD 65CS

dgoodhue · Post by **dgoodhue** » Sun Aug 19, 2007 6:13 am

What is the mounting hole diameter of these?

BigDaddy · Post by **BigDaddy** » Sun Aug 19, 2007 8:25 am

On my box it lists the cut out dimension as 5.63 inches(143mm). I think that's what you were asking.

HoseHead · Post by **HoseHead** » Sun Aug 19, 2007 3:55 pm

The holes are round.

My manual here indicates:

Cut Out Dimension - 142mm
Mounting Depth - 73mm

I have 2 complete BNIB. Bough them on speculation for future installs. Are they good sets? The grills are brutal ugly.

H

Post by **mr tibbs** » Sun Aug 19, 2007 4:49 pm

HoseHead wrote:The holes are round.

My manual here indicates:

Cut Out Dimension - 142mm
Mounting Depth - 73mm

I have 2 complete BNIB. Bough them on speculation for future installs. Are they good sets? The grills are brutal ugly.

H

Them Canadian measurements do no good here in the US. We have to have it our way in order to understand.

HoseHead · Post by **HoseHead** » Sun Aug 19, 2007 5:00 pm

142 mm = 5.59055 inches
73mm = 2.87402 inches

http://www.sciencemadesimple.com/length_conversion.php

Even an American can do it......

They're not Canadian, they're International. The US would have to re-school their entire population and it was tough enough teaching them the first time through.

HH

Post by **mr tibbs** » Sun Aug 19, 2007 5:12 pm

HoseHead wrote:142 mm = 5.59055 inches
73mm = 2.87402 inches

http://www.sciencemadesimple.com/length_conversion.php

Even an American can do it......

They're not Canadian, they're International. The US would have to re-school their entire population and it was tough enough teaching them the first time through.

HH

Did I mention we're lazy too?

dgoodhue · Post by **dgoodhue** » Tue Aug 21, 2007 10:13 pm

It appears as though I might need to go for RSD60CS. My door opening is 5.25", but I have the speakers on 3/4" MDF mounted on top of that. Does anyone know if the RSD65's look like they neck down to 5 1/4" at 3/4" down?

BigDaddy · Post by **BigDaddy** » Tue Aug 21, 2007 11:04 pm

It's late and I'm just measuring roughly with a sewing tape that was here on the desk but it looks to me that about 3/4" down its roughly 4 5/8".

Jason

raffex · Post by **raffex** » Wed Aug 22, 2007 12:57 am

you can always trim the metal a bit so the speaker fits if you have the right tool.

jason whats the little amp you have there in your avatar ..

BigDaddy · Post by **BigDaddy** » Wed Aug 22, 2007 6:32 am

Its a scan I did of my first amp. It's an MS250.
The gold inside this amp looks alot darker than all my other amps for some reason.

HoseHead · Post by **HoseHead** » Wed Aug 22, 2007 10:20 am

dgoodhue wrote:It appears as though I might need to go for RSD60CS. My door opening is 5.25", but I have the speakers on 3/4" MDF mounted on top of that. Does anyone know if the RSD65's look like they neck down to 5 1/4" at 3/4" down?

Chainsaw. Bigga hole as you need.

I have two sets here NIB. I get about the same as BigDaddy - 4 5/8" or so. They'll fit with a 3/4" lift. Door panel hack with that bulge?

HH