tantrum 1200 vs JL1000V2.series

hawaii50 · Post by **hawaii50** » Wed Nov 26, 2008 5:44 pm

Anyone can tell me what amp is much better in RMS. It looks as if maybe the tantrum is not pushing enuff watts.

I am currently running a single JL 13.5/W-7 off of the tantrum 1200 amp. BUt it seems like its maybe not stable at 3 ohms. As when i slam it hard my fuse (80) thats connected to my battery pops. (4 gauge from the battery straight to the amp) The Jl is in its prowedge sealed box.

Ive heard of people on this site going to 2 ohms off the tantrum but not 3 ohms.

Im wondering maybe i should trade my tantrum for ther JL 1000v2 amp any suggestions comments ....?

Is anyone running a JL-W-7 off this amp?.

Post by **Bfowler** » Wed Nov 26, 2008 6:08 pm

dude...the tantrum is a monster. i have never seen one birth below 1400 @ 4ohms....

3 ohms would be perfect for it. 2 i dont really like to do

Post by **fuzzysnuggleduck** » Wed Nov 26, 2008 6:19 pm

I'd take the Tantrum. Your fuse blowing problem is solvable. You just need to systematically eliminate possibilities and apply some critical thinking.

If you have any questions, just ask! There are very knowledgeable people here

hawaii50 · Post by **hawaii50** » Wed Nov 26, 2008 9:36 pm

Im just wondering if my tripath chip is faulty? Does anyone know if my tripath chip is done?. Will the amp still work if the chip is damaged? I think im going to upgrade my power wire to 0/1 .

Post by **stipud** » Thu Nov 27, 2008 7:47 am

Step 1: Turn off bass boost...
Step 2: http://phoenixphorum.com/gain-setting-w ... vt280.html
Step 3: Do a barrel roll.

MW3 · Post by **MW3** » Thu Nov 27, 2008 12:46 pm

1200.1 will blow 80 amp fuses at high volume.

Go with a 100 or even 200 amp fuse. That fuse is not going to protect the amp anyway, its will only protect your car if that wire is ever shorted.

hawaii50 · Post by **hawaii50** » Thu Nov 27, 2008 1:03 pm

But the manual states not to go higher than an 80. Wouldnt I damage the amp?. Should I first change my power wire to 0/1. first? To see if it fixes my problem.? The change to higher fuse.

Mackenzie · Post by **Mackenzie** » Thu Nov 27, 2008 1:24 pm

Higher rated fuses wont hurt anything.. Hell, put a 300amp fuse on if you want.

dako · Post by **dako** » Thu Nov 27, 2008 7:54 pm

you might want to send it in for repair if you feel it's not living up to its potential. all i know is after getting my tantrum 1200 back from PG and running it to 2 RSDC 12 subs, it's disturbing.

brenzbmr@sb · Post by **brenzbmr@sb** » Thu Nov 27, 2008 10:45 pm

there is probably nothing wrong with your amp

put a bigger fuse

you have a beasst of an amp.

hawaii50 · Post by **hawaii50** » Thu Nov 27, 2008 11:54 pm

Okay Thank you all for your help..

Post by **stipud** » Fri Nov 28, 2008 7:10 am

Did you turn off bass boost yet?

All it does is add distortion, and bias towards a single note. Keeping your bass boost off will make any amp work much better.

denim · Post by **denim** » Mon Dec 01, 2008 6:35 am

stipud wrote:Step 1: Turn off bass boost...
Step 2: http://phoenixphorum.com/gain-setting-w ... vt280.html
Step 3: Do a barrel roll.

No preemptive barrel rolls allowed?

Post by **stipud** » Mon Dec 01, 2008 7:24 am

denim wrote:
stipud wrote:Step 1: Turn off bass boost...
Step 2: http://phoenixphorum.com/gain-setting-w ... vt280.html
Step 3: Do a barrel roll.
No preemptive barrel rolls allowed?

No, but handstands are certainly possible

scorpio86 · Post by **scorpio86** » Mon Dec 01, 2008 8:26 am

ya'll kill me ^^