Page 1 of 1
Ampli for Stroker 15"D
Posted: Sat Jan 02, 2010 6:30 am
by tridione
Hi everyone!
I don't found notice about this my problem.
I have in my car MS275 tweeter, MS275 mid, MS2125 bass, and I search good ampli for my sub CerwinVega Stroker 15"D (2 voice coils - 4 ohm - max. tot. 1200 Watt RMS), in vented box of 4.60 Cubic Feet. I have loudspeakers is from italian company: RES.
Please, can you tell me the best solution? (MS2250, Ti1200, ZPA 0.5, or other?)
Thanks
Posted: Sat Jan 02, 2010 8:14 am
by joerg
I would use two MS2125´s for your Stroker 15D4.
The original MS2250 is pretty much useless as u will have to run the wired to 8Ohms unless u got the shroud for cooling it and run it 2Ohms (Not recommended). The MS2250TA can do 2Ohms mono and will give u arround 1100Watts.
Posted: Sat Jan 02, 2010 10:03 am
by stipud
I would use your MS2125 at 2 ohms bridged. At worst you would have to put a fan on the amp, but I think it would work fine without one. The MS2125 works a lot better at 2 ohms than the MS2250 does! You should expect about 750 watts of dynamic power out of it.
Posted: Sat Jan 02, 2010 10:51 am
by tridione
Thanks.
I asked precisely because I was not sure to use an MS2250 for Stroker 15D. The Stroker 15D requires a lot of power to sound good.
Instead of using 2 MS2125 at 4 ohms, if I use a ZPA 0.5, or Ti 1200?
Bye
Posted: Sat Jan 02, 2010 4:47 pm
by phoenixgold79
zpa works well....
if you need i got a xenon 1200.1 in warranty...
item
Posted: Sat Jan 02, 2010 5:14 pm
by kg1961
i have a ms2250ta and fan shroud if you need one
its in the us right now with Borgat
i have 500us into it plus shipping
Re: item
Posted: Mon Jan 04, 2010 2:37 pm
by tridione
kg1961 wrote:i have a ms2250ta and fan shroud if you need one
its in the us right now with Borgat
i have 500us into it plus shipping
Thanks,
I'm not shure to use a ms2250,I need to think, but I remember your offer.
Bye
item
Posted: Mon Jan 04, 2010 6:01 pm
by kg1961
it can handle 2ohm load and tons of power!!!!! and fan cooled i will trade for some amps also
let me know
Posted: Mon Jan 04, 2010 6:34 pm
by stipud
With the fan shroud the MS2250 TA edition can handle 2 ohms bridged nicely. The original MS2250 should only do 4 ohms bridged, even with fans.
item
Posted: Mon Jan 04, 2010 6:37 pm
by kg1961
like i said i have it do you cash in hand?7.5/10 on the amp and 8.5/10 on the shroud very good deal.....
Posted: Thu Jan 07, 2010 4:59 am
by tridione
Thanks to all,
I'm a little be undecided, my idea is the ZPA 0.5, but little problem.......$
too expensive! In europe is not easy to find, in USA no problem, but shipping is terrible.
Posted: Thu Jan 07, 2010 5:36 am
by joerg
Spiritofnorway has one for sale, i think! He´s from austria, so shipping wouldn´t be that bad! Shoot him a message if u are interested
Posted: Thu Jan 07, 2010 7:09 am
by stipud
Keep in mind the ZPA prefers 1 and 4 ohm loads. In order to play 2 ohm, you have to modify the circuit board!