Phoenix Gold Phorum

I will not reveal everything at once ...
But it is what their own ..
But unfortunately there are still missing some parts, such as ports. There will be many more photos of the building but a little patience ..

Geri

wow

so far so good !

thanks for almost sharing.

uhhh, ok then.....

Nice sink!

And as I said there are more pictures .....

is that a towel or a bed comforter? Cotton or what?

could you show us some pics of the screws used?

Unfortunately I can not print is still in progress and will take some time ...
Once I have more pictures I will hire them .?????

I am really confused.

All you have shown is a heatsink. Is there something special I am missing?

You guys sure are impatient.

I was hoping it ws egyption cotton.....

So I have been impatient to tell you ?????
But I still have a photo

200St.

wow, capacitors.......

are they charged already?

I am guessing you should change this project to "High Current FAS", instead of "High Voltage FAS". I can't see how a box of capacitors has anything to do with high voltage...

this thread is too funny!

keep up the good work geri!

no seriously is that egyption cotton or what because if it is, it is probably the most valuable thing you have given us so far.

ttocs wrote:no seriously is that egyption cotton or what because if it is, it is probably the most valuable thing you have given us so far.

^^^^^^^^^^ LOL too funny

[quote = "mhyde71"] diesen Thread zu funny!

Keep up the good work geri! : arrow: [/ quote]

Hi....
The name will remain .....
Because the Plexiglas is now finished.
It will be installed 200 St. Kondensatorren.
200x Elko NRLMW103M16V 25x25mm RM10
10000µF/16V, 4000h/105°C
And another quick photos.
Copper is the Kondensatorren to connect with the PCB, with the PCB (print), or to the mill is because the copper bars will be admitted to everything, in the heat sink is the place.
Regards Geri

I am unsure of what the hell is going on with this....hey, Geri....what caps are those? uf, voltage, and are they by chance 35 by 35 chassis. hmmmmm

I think he is using the copper rails and caps to build a giant capacitance bank....cool project if that is indeed what you are doing....uhhhhh...be careful my friend....you'll have to be really careful with loading those and I am guessing you don't intend to just go parallel in runs.....

Am I right Geri? Is this what you are up to.....It is an interesting idea....I would have just done an ms 250 sink full....that is a lot of potential for issue right there and it isn't the safest thing to attempt....

yea ya lost me on that one too..........

I believe he intends to build a giant ms powercore...that case will be a huge capacitor most likely to match his fas in an install

bogart wrote:I believe he intends to build a giant ms powercore...that case will be a huge capacitor most likely to match his fas in an install

Hello
YES it is really a giant capacitor in the heat sink of a SOFAS ...
And his place between FAS and SOFAS will find supplies of the two MS2125 ...

Something like ...

do you plan on bumpin up the rail voltage, any circuit rework planned? I like the idea and know its gonna look really cool but a battery would be a better choice for reserve power...

Either way Id like to see this done as it gives everyone creative ideas and insperation to do mods to there ms amps for performance gains no matter how small..most of us like to tinker and would pay for the plans to do these type of things...my 02

which by the way,there should already be a how to improve a ms amp with every available mod to do to them archived here on this forum?? I have noticed whenever that type of info gets posted...it get deleted (pics,txt) later on??

anyways give us more pic's!!!!

You better sell me that sink! J/K

Good luck with the built Geri!!! Keep us up to date