Hi all.
First of all - let me introduce myself.
As you might have figured out - my name is Kurt - and living at the westcoast of Norway (not too far away from Pedi's place).
And it was a visit to Pedi's place some months ago that convinced me to continue the carstereo hobby (I've been out of this game since the mid 90's). Pedi showed me all the good old PG stuff he's been collecting over the years - so; here I am
I've been reading this phorum alot, and learned alot. I've successfully recap'ed both of my MS-275's based on the guides here - and 3 more amps on it's way.
So to the question:
My 2 MS-275 (rev G & H), have different bottom plates when it comes to the wiring diagram (polarity L+R (and bridge)
If you look at the pictures - both amps shows + - + - L & R channel, but when flipping them over the plate on the rev H is showing me - + - + ??
The SN matches the SN on the printboard.
Anyone know about this?
Seen this before?
Introduction + question regarding MS-275
Introduction + question regarding MS-275
VW Polo -96
HU - DEH-X6600DAB
Front - something DLS 6,5" component
2x Soundqubed HDS-208
3x MS-275
1x MS-2125
2x ZX600ti
HU - DEH-X6600DAB
Front - something DLS 6,5" component
2x Soundqubed HDS-208
3x MS-275
1x MS-2125
2x ZX600ti
-
- Posts: 1653
- Joined: Sun May 06, 2012 8:01 am
Re: Introduction + question regarding MS-275
LOL typo ...only way to know for sure is to see where the speaker wires from the terminal inside go to (two of them go to the signal ground...the two in the middle should be it).
The side covers are correct...outer left is positive while outer right is negative...two inners are signal ground (remember one channel is inverted for mono operation).
The side covers are correct...outer left is positive while outer right is negative...two inners are signal ground (remember one channel is inverted for mono operation).
Re: Introduction + question regarding MS-275
+L and -R is always what I was told
what else can I say I am a grumpy asshole most of the time.
Re: Introduction + question regarding MS-275
I'll have to check them both - againtrickyricky wrote:LOL typo ...only way to know for sure is to see where the speaker wires from the terminal inside go to (two of them go to the signal ground...the two in the middle should be it).
The side covers are correct...outer left is positive while outer right is negative...two inners are signal ground (remember one channel is inverted for mono operation).
Better keep this one I think. Didn't know that PG made mistakes - hehe
VW Polo -96
HU - DEH-X6600DAB
Front - something DLS 6,5" component
2x Soundqubed HDS-208
3x MS-275
1x MS-2125
2x ZX600ti
HU - DEH-X6600DAB
Front - something DLS 6,5" component
2x Soundqubed HDS-208
3x MS-275
1x MS-2125
2x ZX600ti
Re: Introduction + question regarding MS-275
Welcome KurtKurten75 wrote:Hi all.
First of all - let me introduce myself.
As you might have figured out - my name is Kurt - and living at the westcoast of Norway (not too far away from Pedi's place).
And it was a visit to Pedi's place some months ago that convinced me to continue the carstereo hobby (I've been out of this game since the mid 90's). Pedi showed me all the good old PG stuff he's been collecting over the years - so; here I am
I've been reading this phorum alot, and learned alot. I've successfully recap'ed both of my MS-275's based on the guides here - and 3 more amps on it's way.
So to the question:
My 2 MS-275 (rev G & H), have different bottom plates when it comes to the wiring diagram (polarity L+R (and bridge)
If you look at the pictures - both amps shows + - + - L & R channel, but when flipping them over the plate on the rev H is showing me - + - + ??
The SN matches the SN on the printboard.
Anyone know about this?
Seen this before?
Another memder from Norway. I haven't thought about this, I'll check mine during the weekend, i have 6 MS275 and they are from rev c to h i think.
3x MPS2240
5x MPS2500
1x MS2250
1x MQ430 (white)
1x MQ430 (gray)
3x MS275 (white)
3x MS275 (gray)
ax406a
ax204
5x MPS2500
1x MS2250
1x MQ430 (white)
1x MQ430 (gray)
3x MS275 (white)
3x MS275 (gray)
ax406a
ax204
Re: Introduction + question regarding MS-275
Welcome Kurt. Wow, I didn't know that PG was so popular in Norway.
I haven't gotten into MS amps yet, but that's a very interesting find. I would have to believe that PG didn't just silkscreen one like that, there must be a batch of misprinted amps out there.
I haven't gotten into MS amps yet, but that's a very interesting find. I would have to believe that PG didn't just silkscreen one like that, there must be a batch of misprinted amps out there.
A few of these and a few of those.
Creator of www.phoenixgoldregistry.com
hit me up to add your limited edition amps.
Creator of www.phoenixgoldregistry.com
hit me up to add your limited edition amps.
-
- Posts: 1653
- Joined: Sun May 06, 2012 8:01 am
Re: Introduction + question regarding MS-275
Yeah but who looks at the bottom diagram when hooking up the amp and having the silkscreen panels.
Re: Introduction + question regarding MS-275
Thanks all for the warm welcome.
Not a big deal - but wanted to know if this was a common issue
Not a big deal - but wanted to know if this was a common issue
hehetrickyricky wrote:Yeah but who looks at the bottom diagram when hooking up the amp and having the silkscreen panels.
VW Polo -96
HU - DEH-X6600DAB
Front - something DLS 6,5" component
2x Soundqubed HDS-208
3x MS-275
1x MS-2125
2x ZX600ti
HU - DEH-X6600DAB
Front - something DLS 6,5" component
2x Soundqubed HDS-208
3x MS-275
1x MS-2125
2x ZX600ti
Re: Introduction + question regarding MS-275
And by the way, it's Pedis fault that I'm addicted and infected With the phvirus also
3x MPS2240
5x MPS2500
1x MS2250
1x MQ430 (white)
1x MQ430 (gray)
3x MS275 (white)
3x MS275 (gray)
ax406a
ax204
5x MPS2500
1x MS2250
1x MQ430 (white)
1x MQ430 (gray)
3x MS275 (white)
3x MS275 (gray)
ax406a
ax204
Re: Introduction + question regarding MS-275
PG typo's ARE a common issue. Their literature is littered with typo's.Kurten75 wrote:Thanks all for the warm welcome.
Not a big deal - but wanted to know if this was a common issue
hehetrickyricky wrote:Yeah but who looks at the bottom diagram when hooking up the amp and having the silkscreen panels.
XS2300, XS2500, XS2300, X200.4, X100.2, Ti21000.4, Roadster 66
I'm gonna become a civil engineer. I'm gonna design septic tanks for playgrounds. Little kids can take shits! You idiot, what the hell do you do?
I'm gonna become a civil engineer. I'm gonna design septic tanks for playgrounds. Little kids can take shits! You idiot, what the hell do you do?