PG RSD 65CS
Posted: Sun Aug 19, 2007 6:13 am
What is the mounting hole diameter of these?
Phoenix Gold Phorum
Celebrating the Phoenix Gold legacy, and oldschool car audio!
https://www.phoenixphorum.com/
PG RSD 65CS
Page 1 of 1
Posted: Sun Aug 19, 2007 8:25 am
On my box it lists the cut out dimension as 5.63 inches(143mm). I think that's what you were asking.
Posted: Sun Aug 19, 2007 3:55 pm
The holes are round. 
My manual here indicates:
Cut Out Dimension - 142mm
Mounting Depth - 73mm
I have 2 complete BNIB. Bough them on speculation for future installs. Are they good sets? The grills are brutal ugly.
H
My manual here indicates:
Cut Out Dimension - 142mm
Mounting Depth - 73mm
I have 2 complete BNIB. Bough them on speculation for future installs. Are they good sets? The grills are brutal ugly.
H
Posted: Sun Aug 19, 2007 4:49 pm
Them Canadian measurements do no good here in the US. We have to have it our way in order to understand.HoseHead wrote:The holes are round.
My manual here indicates:
Cut Out Dimension - 142mm
Mounting Depth - 73mm
I have 2 complete BNIB. Bough them on speculation for future installs. Are they good sets? The grills are brutal ugly.
H
Posted: Sun Aug 19, 2007 5:00 pm
142 mm = 5.59055 inches
73mm = 2.87402 inches
http://www.sciencemadesimple.com/length_conversion.php
Even an American can do it......
They're not Canadian, they're International. The US would have to re-school their entire population and it was tough enough teaching them the first time through.
HH
73mm = 2.87402 inches
http://www.sciencemadesimple.com/length_conversion.php
Even an American can do it......
They're not Canadian, they're International. The US would have to re-school their entire population and it was tough enough teaching them the first time through.
HH
Posted: Sun Aug 19, 2007 5:12 pm
Did I mention we're lazy too?HoseHead wrote:142 mm = 5.59055 inches
73mm = 2.87402 inches
http://www.sciencemadesimple.com/length_conversion.php
Even an American can do it......
They're not Canadian, they're International. The US would have to re-school their entire population and it was tough enough teaching them the first time through.
HH
Posted: Tue Aug 21, 2007 10:13 pm
It appears as though I might need to go for RSD60CS. My door opening is 5.25", but I have the speakers on 3/4" MDF mounted on top of that. Does anyone know if the RSD65's look like they neck down to 5 1/4" at 3/4" down?
Posted: Tue Aug 21, 2007 11:04 pm
It's late and I'm just measuring roughly with a sewing tape that was here on the desk but it looks to me that about 3/4" down its roughly 4 5/8".
Jason
Jason
Posted: Wed Aug 22, 2007 12:57 am
you can always trim the metal a bit so the speaker fits if you have the right tool.
jason whats the little amp you have there in your avatar ..
jason whats the little amp you have there in your avatar ..
Posted: Wed Aug 22, 2007 6:32 am
Its a scan I did of my first amp. It's an MS250.
The gold inside this amp looks alot darker than all my other amps for some reason.
The gold inside this amp looks alot darker than all my other amps for some reason.
Posted: Wed Aug 22, 2007 10:20 am
Chainsaw. Bigga hole as you need.dgoodhue wrote:It appears as though I might need to go for RSD60CS. My door opening is 5.25", but I have the speakers on 3/4" MDF mounted on top of that. Does anyone know if the RSD65's look like they neck down to 5 1/4" at 3/4" down?
I have two sets here NIB. I get about the same as BigDaddy - 4 5/8" or so. They'll fit with a 3/4" lift. Door panel hack with that bulge?
HH