Page 1 of 1
3 dvc4ohm subs at 2.66 ohm on 1200.1
Posted: Sat Feb 16, 2008 5:59 pm
by thedeal7235
has anyone ever ran a 1200.1 below 2ohm? right now, b/c i have 3 4ohmdvc subs they are wired to be 2.66; wondering if anyone thinks the load of 1.33 ohm on the 1200.1 would be stable or not?????
Posted: Sat Feb 16, 2008 6:08 pm
by thedeal7235
Minimum Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ohm; that is from the ti 1200.1 MinimumSPECIFICATIONS
Continuous Output Power at 1% THD (watts):
Titanium 1200.1
Into 4 ohms @ 12.5 Vdc (IASCA/USAC) . . . . . . . . .250 x 1
Into 4 ohms @ 14.4 Vdc . . . . . . . . . . . . . . . . . . . . .600 x 1
Into 2 ohms @ 14.4 Vdc . . . . . . . . . . . . . . . . . . . .1200 x 1
Into 2 ohms @ 14.4 Vdc (Dynamic Power) . . . . . .1400 x 1
Recommended Fuse Size . . . . . . . . . . . . . . . . . .120 Amps
Dimensions . . . . . . . . . . . . . . . . . .25.5L x 10.0W x 2.35H
Common Specifications
Frequency Response . . . . . . . . . . . .±1dB, 20Hz to 20kHz
Signal to Noise Ratio (A-weighted) . . . . . . . . . . . . .>110dB
Input Sensitivity . . . . . . . . . . . . . . . .200 millivolts to 6 volts
Lowpass Crossover Frequency . . . . . . . . . .50Hz to 250Hz
Highpass Crossover Frequency . . . . . . . . . .40Hz to 800Hz
Subsonic Frequency . . . . . . . . . . . . . . . . . . . .5Hz to 50Hz
Crossover Slopes . . . . . . . . . . . . . . . . . . .24dB per Octave
Bass EQ Level . . . . . . . . . . . . . . . . . . . . . .-12dB to +12dB
Bass EQ Range . . . . . . . . . . . . . . . . . . . . .30Hz to 120Hz
DC Input Voltage Range . . . . . . . . . . .10 volts to 15.5 volts
Typical Current Draw at Idle . . . . . . . . . . . . . . . . . .2 amps
Minimum Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ohm
Due to ongoing research and development, features,
specifications and availability are subject to change without notice Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ohm
Posted: Sat Feb 16, 2008 6:12 pm
by AVICJR
Posted: Sat Feb 16, 2008 6:13 pm
by mr tibbs
NM, ninja edit!
Posted: Sat Feb 16, 2008 6:30 pm
by thedeal7235
i understand guys, but whats up with the 1ohm min. laod???????????????
Posted: Sat Feb 16, 2008 7:00 pm
by mr tibbs
I would dare say that is a best case scenario sales tactic they tried to play. I would stick with what experience has to say rather than a piece of paper.
Posted: Sat Feb 16, 2008 7:07 pm
by thedeal7235
i know , thanx for link to the link- but someone said they ran theres at 1.5-its killing me to not try-however i dont feel like sending in yet another amp to pg for repair