Page 1 of 1
12d elite needs enclosure
Posted: Wed Aug 13, 2008 2:30 pm
by phoenixcat
hi, i got this sub and i'm finishing my install, i need to know what is the best enclosure for sq (internal volume? ported?closed? )
i can hang up to 3 cu.ft. of internal volume.
thanks
Posted: Wed Aug 13, 2008 2:32 pm
by stipud
I would recommend either of the musical enclosures in the manual.
http://download.phoenixphorum.com/Manua ... ev8.02.pdf
Looks like the musical ported box is 2.75cuft... so you could fit it.
Posted: Wed Aug 13, 2008 2:52 pm
by phoenixcat
thank you, i lost the original depliant
.
another question: i want to run that sub with a zpa 0.5, is good @ 2 ohm or i mod it cutting the 2 diodes?
Posted: Wed Aug 13, 2008 3:01 pm
by stipud
Try it first... if it cuts the volume too much, then you may have to try the mod.
Posted: Thu Aug 14, 2008 3:24 pm
by culzero
I ran a 12d elite on a zpa0.5 for a couple years. sounded great, though it did want some more power
Posted: Sat Aug 16, 2008 12:00 pm
by drivingdadevil
You sould contact Pete at Hexibase dot com. He designed my enclosure for my two Ti Elites and it sounds amazing.
Posted: Sat Aug 16, 2008 12:38 pm
by phoenixcat
i'm finishing the enclosure for my baby right now
lik pg's specs
Posted: Sat Aug 16, 2008 6:31 pm
by drivingdadevil
Looks good so far. Are you going to port it or go sealed?
Posted: Sat Aug 16, 2008 6:32 pm
by drivingdadevil
Looks good so far. Are you going to port it or go sealed?
Posted: Sat Aug 16, 2008 7:05 pm
by deathcloud
Omg those are some bad ass amps. LET ME GET ONE!
Posted: Sat Aug 16, 2008 9:45 pm
by Wakeup
Ya looking good! Keep us all informed. I have a TI 12 D Elite in a sealed enclosure...sounds good...not huge bass wise, so if you are going for Q...you might go Sealed. My box is braced pretty well, and is 1 3/4 " think. If i remember correctly, it weighs close to 100 Pounds...
Pictures here:
http://s200.photobucket.com/albums/aa63 ... ite%20sub/
Posted: Sun Aug 17, 2008 1:52 am
by phoenixcat
deathcloud wrote:Omg those are some bad ass amps. LET ME GET ONE!
if you got a ms-1000 i can give you my zpa's
i'm going to a ported enclosure (i like more than sealed. . .) 75 lt @ 28 hz like pg specs, i use 19mm mdf and some fiberglass .
is hard to find a spare voice coil for this sub? (not the spl, only the original)
Posted: Sun Aug 17, 2008 10:34 pm
by brenzbmr@sb
well i have a extra cone both spl and regular...
second you should all hear mine.
it has gobs of low end and it sounds fricken nutz outside the car....
Posted: Mon Aug 18, 2008 1:09 pm
by phoenixcat
today's work
tomorrow i drill the enclosure for the tube and i try it
Posted: Mon Aug 18, 2008 1:31 pm
by AVICJR
Just as a precautionary method you may want to build the white ZPA (amp rack) up like you did the black one so that it isn't mounted directly to the box. I used to mount my amps directly to my box also but I never owned a ZPA.
Posted: Mon Aug 18, 2008 2:05 pm
by phoenixcat
i mount all zpas on rubber silentblocks (for prevent damaging by vibrations
), under the 0,3 there is another box for pxa-h701 and tld66.
is hard to explain all in english, sorry
Posted: Wed Aug 20, 2008 12:03 am
by Wakeup
brenzbmr@sb wrote:well i have a extra cone both spl and regular...
second you should all hear mine.
it has gobs of low end and it sounds fricken nutz outside the car....
REMEBER!!! I have Dibs if you should ever sell the SPL Cone!!! PLEASE!
