from screw hole to screw hole (completed)

JK · Post by JK » Mon May 17, 2010 1:19 pm

i need to know the distance from mounting hole to mounting hole. it needs to be measured rite in the middle of the hole to hole. ms2125/2500/2250=16 1/2 FRANK= 27 1/2 SOFA= 25 MS1000= 33 1/2 I need to know the distance on the SOFA and the MS1000. THANK YOU! THESE ARE THE ANSWERS I WAS LOOKIN FOR>>

Post by **mhyde71** » Mon May 17, 2010 1:29 pm

ms 1000 i believe stands to reason 33 1/2"
sofa 25"

if i understand you correctly

MS275 sink is 8.5" LONG (lets call it long now for sake of argument- anyways),(width is 12"), but the 2125 is 17" long (and width of 12")

and it looks as though the centers are 1/4" off each end- NO?!? might be wrong... but inclined to think you line/stack up a row of 275's, 430's, 2125', and look down all those mounting holes like a barrel of a gun... straight down/through)

(2125) 17" + (275) 8.5" = 25.5" - .5 = 25" coc (center on center),

MS1000 would be 17 x 2 = 34 - .5 = 33.5 coc

Right? i think so anyways

ARE YOU SURE that the FAS is 27.5"???

isnt the 430 = 12" and the 2125 = 17" so that would be 29 - (.25 x 2) .5

just off the cuff- my thoughts-
Later i will actually go measure unless someone beats me to it.
I have the following 275, 430, 2125/2250, 1000 and bid grandpa surfboard sinks all naked and stripped for easy measuring (and photo taking

)

Thanks for bringing the question up though- I prolly would have let the chance pass by before taking picture of all together like that- prolly will not happen ever again like that with these sinks whence they land in their owners hometown/land... before loosing the chance i should get on that...!

Isnt that what you call (all the planets- i mean sinks- lined up)

Maybe i should take pic of all the sinks lined up along side of the entire family- up to the big daddy surfboard...

watch guys this should be neat!

m

JK · Post by JK » Mon May 17, 2010 1:41 pm

on the ms275. 8 inches from the center to center. that's what im lookin for on the sofa/ms1000

Post by **mhyde71** » Mon May 17, 2010 1:46 pm

okay so it is 25 (not 25.5") so yeah then thats right
I thought the 275 was 8.5...cool

BUT yeah the 2125 sink is 17" so the 1000 sink is two of those - to the T- 17*2=34 (-.5)= 33.5 coc (will confirm later this eve for us though)
just like the surf board is exactly 17 x 3 = 51" long- so the ms 1000 coc would be 33.5 (1/4" in from each end)

JK · Post by JK » Mon May 17, 2010 2:02 pm

i dont like to speak on something that's not finished, but things are comin along. i made a couple changes for legal reasons, but nothing no one will notice. i have shot u some pm's 71 and it would save me some time if u could help me. i will be posting pictures soon. i have only so much control, so i dont have a time frame to as when they will be posted.

. i guess i left it kinda open to what im talkin about.. RESULTS SPEAK!

Post by **mhyde71** » Mon May 17, 2010 2:06 pm

yeah JK

please send a revised/updated Pm when chance-

i know we were going back and forth on a number of things- BUT i think i may have confused you with someone else and their screw requests...

pls thx
matt

JK · Post by JK » Mon May 17, 2010 2:38 pm

pm sent!

JK · Post by JK » Mon May 17, 2010 7:38 pm

if anyone can take a measurement it would be perfect.. thanks!

JK · Post by JK » Tue May 18, 2010 10:24 am

can anyone help? maybe i should just figure out the length of the amps in question. then pull a measurement from the end to the center of my hole and there is my answer. ill post it here in a minute when i figure it out.

JK · Post by JK » Tue May 18, 2010 11:18 am

mhyde71 wrote:ms 1000 i believe stands to reason 33 1/2"
sofa 25"

if i understand you correctly

MS275 sink is 8.5" LONG (lets call it long now for sake of argument- anyways),(width is 12"), but the 2125 is 17" long (and width of 12")

and it looks as though the centers are 1/4" off each end- NO?!? might be wrong... but inclined to think you line/stack up a row of 275's, 430's, 2125', and look down all those mounting holes like a barrel of a gun... straight down/through)

(2125) 17" + (275) 8.5" = 25.5" - .5 = 25" coc (center on center),

MS1000 would be 17 x 2 = 34 - .5 = 33.5 coc

Right? i think so anyways

ARE YOU SURE that the FAS is 27.5"???

isnt the 430 = 12" and the 2125 = 17" so that would be 29 - (.25 x 2) .5

just off the cuff- my thoughts-
Later i will actually go measure unless someone beats me to it.
I have the following 275, 430, 2125/2250, 1000 and bid grandpa surfboard sinks all naked and stripped for easy measuring (and photo taking )

Thanks for bringing the question up though- I prolly would have let the chance pass by before taking picture of all together like that- prolly will not happen ever again like that with these sinks whence they land in their owners hometown/land... before loosing the chance i should get on that...!

Isnt that what you call (all the planets- i mean sinks- lined up)

Maybe i should take pic of all the sinks lined up along side of the entire family- up to the big daddy surfboard...

watch guys this should be neat!

m

u are 100% rite MS1000=33 1/2 and the sofa is 25.. frank 27 1/2 and the2250 16 1/2 thanks!

Post by **joerg** » Tue May 18, 2010 11:36 am

I just got home and took measurements!

FAS-----------697mm
SOFAS--------633mm
Nickel---------851mm
MS2250-------419mm

Hope that helps

Post by **mhyde71** » Tue May 18, 2010 11:59 am

FAS-----------697mm = 27.5"
SOFAS--------633mm = 25"
Nickel---------851mm = 33.50
MS2250-------419mm = 16.5"

INM & just like i said up top!

whew! so good to know i was right once!

JK · Post by JK » Tue May 18, 2010 1:02 pm

thanks! i would rather make sure i was 100% rite. id rather ask than assume. this is very helpfull in the making of the 4 sizes of shrouds that are in the making. insted of 18 gauge steel. they will be 16 gauge aluminum. its a perfect match to the original shrouds. as well as the holes. the only thing left is locating baulk screws. that is for the making of the shrouds