Okay, I put all this in the car last night...just to test the amp really and see what she will do. Over the next month or so I will switch a few thing around and start building the box for the mojo, which will eventually be a permanent fixture with this amp.
The subs I am running running for the time being are 2 ti15s running two ohms. The amp is rated at 1600 rms at 2 ohms but it is doing much more from the feel of the subs. Now there is obviously some over-head but it will move them and hard with near zero gain...Morgan told me the amps are built to love one ohm and I am looking forward to dropping the impedance down for the 2400...plus would be my bet.
More later .... on with a few teasers of my latest getto install. You guys have seen what I can do...and this is about the state my car has been in for the last two years okay...photo issue resolved I think
If these pics are huge I am going to have to find some better photo software
Attachments
IMGP1061.jpg (67.89 KiB) Viewed 6803 times
IMGP1062.jpg (35.95 KiB) Viewed 6803 times
IMGP1063.jpg (27.9 KiB) Viewed 6803 times
IMGP1064.jpg (68.22 KiB) Viewed 6803 times
IMGP1065.jpg (28.45 KiB) Viewed 6803 times
IMGP1066.jpg (29.61 KiB) Viewed 6803 times
IMGP1067.jpg (82.86 KiB) Viewed 6803 times
IMGP1068.jpg (25.84 KiB) Viewed 6803 times
Last edited by bogart on Sat Jul 11, 2009 10:02 pm, edited 1 time in total.
you forgot the 1rst rule man, always fuse power wires with in 12" of the batteries and this includes power wires and rear-located 2nd batts. You have a fuse mounted there but it is too close to the amp to protect the wire. What will happen if that wire shorts out between the battery and the fuse? You will weld that cable to the chassis.
It is a 900.7 running 4 ohm 4 channel....I do need a bunch of breakers...I had a box of em and can't find em anywhere. Those ti 15s do pretty good in that box.
The box was harolds...I would like to get the ti's in the big ole 5ft sealed per on this power and see just how low she'll run...but it is nice as it slide right in through the front with an inch or two to spare.
I'm going to be pulling the ti crossovers and the 900.7 and run musicomp two ways as they have the -6 db tweet attenuation and the outlaw is going in once I can go get mdf....
no it doesn't...it has louvers across the top to open the whole amp up and the sink is just stupid heavy...I am going to silverton falls today and that will give me an hour and some change to really let the amp do what it is going to do...as of yet It hasn't gotten hot at all with the louvers open...
It may at one ohm but at two it appears to be ok...going easy on the ti subs though...they were never really made to see 2k of current
That box was made to fit in a 95 Accord so it's made to minimum spec so I could also fit the amps in there aswell.............
Attachments
Ti15 Accord install.JPG (160.98 KiB) Viewed 6753 times
DCP02624.JPG (146.16 KiB) Viewed 6753 times
Those tender little burgers with them little, itty-bitty grilled onions that just explode in ya mouth like flavor crystals every time you bite into one.. just makes me want to burn this muthafuka down.... Come on, Pookie, let's burn this muthafuka down!!!
Those tender little burgers with them little, itty-bitty grilled onions that just explode in ya mouth like flavor crystals every time you bite into one.. just makes me want to burn this muthafuka down.... Come on, Pookie, let's burn this muthafuka down!!!
I will be the first to state... that Exile amp rocks! I know Bogart stated to me that the box for his 15's where too small.... but as he was explaining that I had a hard time hearing him! Those babies where moving some serious air, that it actually was removing some of his words. I'm gonna run 4 Xmax tens in my bronco, thank you very much Mr. B, but after listening to that Exile 2400.1 and those 15's, the runner is gonna have some BIG 15's and maybe a complete exile amp setup! Very impressed.
J/k
