What in the hell?

Need help with your car stereo system? Have a technical question? Post here.
Post Reply
User avatar
smgreen20
Posts: 2873
Joined: Wed Dec 20, 2006 11:23 am
Location: Somewhere in Between

What in the hell?

Post by smgreen20 »

Ok, it did this last Nov and hasn't done it again untill today. Driving along w/the volume cranked, as I was only going 3 miles down the road, and the amps shut off. As most all here know, I have a PG ZPA0.3 running a set of Dynaudio System 240 MKII's at 150 wrms each side (300 wrms total) and a PG ZPA0.5 to a single TREO SSi10.44 sub wired to 2 ohms mono on the 0.5 set to 900 wrms (for a grand total of 1200 wrms) and the rear stock speakers running off of the Pioneer P980BT HU, for the kids only. The rear speakers, powered by the HU were still playing but that's it. Which leads me to a few things. 1, I have a PG 140 ampere curcuit breaker, that's damn near shot, which I think could be or IS the problem. 2, remote wire on the HU is doing something funky. All connections are secure, 2 guage PG power wire to a distro then into 4 guage Memphis power wire (for the Orange color) and 2 guage PG Ground wire. I feel that it's the Curcuit breaker being so old it's not fully doing its job and that the voltage drops because of it and the amps shut off. I have a 130 ampere alt and have done the big 3 w/4 Guage PG wire and an Optima Yelloy top battery. I'm looking for other possabilities, so please,if you happen to think of some, please tell.
"ZPA's will have the same sound essentially as you get from the MS, they just feature a bigger shinier set of balls."

Install:
http://phoenixphorum.com/viewtopic.php?f=10&t=16998
User avatar
mr tibbs
Forum Goatee
Posts: 3895
Joined: Sun Dec 17, 2006 3:03 pm
Location: The land of morons, I mean mormons.:(

Post by mr tibbs »

I think your on the right track with the circuit breaker. I think you have to look at what would cause both amps to cut out at the same time. Do you have a grounding block that could come loose or are the amps grounded seperatley?
User avatar
smgreen20
Posts: 2873
Joined: Wed Dec 20, 2006 11:23 am
Location: Somewhere in Between

Post by smgreen20 »

Both amps shutting off at the same time is why I look at the remote or the circuit breaker as the fualt. Both amps run to a ground distro block. All conections are good.
"ZPA's will have the same sound essentially as you get from the MS, they just feature a bigger shinier set of balls."

Install:
http://phoenixphorum.com/viewtopic.php?f=10&t=16998
User avatar
stipud
Voltage Ohms
Posts: 14719
Joined: Sat Nov 26, 1983 4:00 am
Location: Burnaby, BC
Contact:

Post by stipud »

Only way I can think of checking is by hooking up a voltmeter to your amps power terminals. If power drops to 0v when it shuts off, it is your breaker, otherwise it is the remote.

You can also try running a short wire from the power lead to the remote wire, and bypass it that way. Then if it doesn't cut out it is likely the remote.
User avatar
smgreen20
Posts: 2873
Joined: Wed Dec 20, 2006 11:23 am
Location: Somewhere in Between

Post by smgreen20 »

Will try the bypassing of the remote wire on Tues. Good point. Some of the simple things are always the hardest to find.
"ZPA's will have the same sound essentially as you get from the MS, they just feature a bigger shinier set of balls."

Install:
http://phoenixphorum.com/viewtopic.php?f=10&t=16998
Post Reply