updates on my box.

brenzbmr@sb · Post by **brenzbmr@sb** » Fri Feb 15, 2008 9:06 pm

this has been fun
as you can see i have finally got it all together and now im working on the ports.
they will fire through the rear deck..

as you can see im tryn to use areo ports with regular schedual 40 pipe

so i had to rabbit a lip into the pipe to accomodate the areo port.

now im actually smoothing things out. i have to put the front of box in first then add the second section that the port goes into, then add the port
through the box and then from the top add the areo ports and glue it together, once in there is no removing.

after that i add the second section and the back

oh btw
i hooked this up in my garage and from 45hz down to about 25 its very dominant.. it shakes my house with about 100 watts from an old alpine amp i have. its not even in the car.

cant wait to run the two ms2125s and put it in the car..

brenzbmr@sb · Post by **brenzbmr@sb** » Fri Feb 15, 2008 9:09 pm

here is the ports

ydnap · Post by **ydnap** » Fri Feb 15, 2008 10:10 pm

ooo they look like the old aeros

brenzbmr@sb · Post by **brenzbmr@sb** » Mon Feb 18, 2008 12:33 am

hooked it up today

its a low end system thats for sure. not very loud but its not bad for a
12 on 500 watts.

but it does get loud on low notes

i will play with tuning some more but i may have to get off the ms amps
and actually get a class d amp so that i can get this thing to
move.

brenzbmr@sb · Post by **brenzbmr@sb** » Sun Feb 24, 2008 11:24 pm

here is an update, i removed everything and now am putting it back in
for good.

here is some pics of the baffel that i made to channel all the air into the cabin.

its totally sealed from bolting it up to the rear seat metal.

ports will be next.

thedeal7235 · Post by **thedeal7235** » Tue May 27, 2008 7:24 pm

hey im redesigning my audi; b4 i had 3 diamond d6 10's in a slot ported box, running off my ti 1200.1; nyways, i put in my 2 rsd 1200.1, and took the third sub out- this way i have a rsd 1200.1 running each sub - im gonna build a new box- seperate air chambers for each sub, but i have enough room to fire the ports up thru the back dash, how do u like it? thank for reply Christian

Post by **fuzzysnuggleduck** » Tue May 27, 2008 9:03 pm

I'm sure you have it all figured out, but from the angle of the photo it doesn't look like there's much room for excursion.

brenzbmr@sb · Post by **brenzbmr@sb** » Sun Mar 14, 2010 12:22 pm

bumping for some to see

Damo95 · Post by **Damo95** » Sun Mar 14, 2010 2:12 pm

That was my thought when i saw that last pic too, fsd..

should be good!

twisted · Post by **twisted** » Sun Mar 14, 2010 6:50 pm

i think its just the picture........... i remember in the other thread the sub is recesed back a bit more than this last photo reveals

NewOldStock · Post by **NewOldStock** » Sun Mar 14, 2010 6:54 pm

fuzzysnuggleduck wrote:I'm sure you have it all figured out, but from the angle of the photo it doesn't look like there's much room for excursion.

if you look just under the sub, you can see where the sub is recessed back 4-5 inches then where the box touches the back wall. Eyes playing tricks on ya.

Tiger · Post by **Tiger** » Sun Mar 14, 2010 8:07 pm

Yikes! Tough 12!

How did this enclosure turn out?

brenzbmr@sb · Post by **brenzbmr@sb** » Sun Mar 14, 2010 9:55 pm

oh i have plenty of room for the excursion, that picture looks bad but trust me i dont have to worry about the surround hitting anything

updates on my box.

updates on my box.

ur ports firing up thru back dash???