Jacampb2 wrote:I'm cutting a batch of 16 boards right now. I am not sure how I am set on components, but I should have a handful done in the next few days.
Spot on
you told me that you would know something around the 21st on
another batch. A man of his word, folks.
1- Zx 400 Ti
1- Ti 600.2
1- Ti 500.4 (resurrected by valeks1)
2- Ti 500.4
2- Ti 1000.2
2-Ti RMD, Lpl, PG 1/0 Ga
Ti 6.5 comps, Ti 5x7 coaxials
I have a little problem. My Bass Cube was installed in my Jetta, the trunk leaked during the last rain storm here and it dripped right on the BC. It looks like it only took out two op amps in the Cube, and I have replacements on order, but until I get it fixed I have no way of testing the remotes, so it will be a while before I can commit any for sale. I have enough components for five remotes, I will keep you all updated on what the status is...
Later,
Jason
M: M100, M44 for a custom amp project
Zx: Zx500, Zx450, Black Zx350
ZxTi: 4 Zx600Ti's, 1 Zx400Ti
Ti: 5 800.1's & 900.7 for a custom amp project. 1 1200.1, 1 1000.2
Tantrum: 2 1200.1's, 1 600.4, 1 500.2
XS: XS6600
Jacampb2 wrote:I have a little problem. My Bass Cube was installed in my Jetta, the trunk leaked during the last rain storm here and it dripped right on the BC. It looks like it only took out two op amps in the Cube, and I have replacements on order, but until I get it fixed I have no way of testing the remotes, so it will be a while before I can commit any for sale. I have enough components for five remotes, I will keep you all updated on what the status is...
When I did the DLM boards I had to order a total of 100 square inches of PCB made to get the rather sizable price break at Oshpark. So, rather than order a ton more of the DLM boards (I already had 20 in the order) I redrew the BC remote boards again and had some of those professionally made as well. I mentioned elsewhere that the US distributor no longer has the switched pots, so I bought a tray from China to make these. I fully intend to put them on Ebay as well because I have a lot of money into potentiometers right now... The Frequency pot now also has a removable shaft. The remote will still fit the factory bracket by panel mounting with the gain pot's threaded shank, but it will no longer be able to be screwed into the back standoff because of the change in the frequency pot style. It still can be easily panel mounted, or mounted in the factory bracket, but you can only use the one mounting point.
Pic:
Later,
Jason
M: M100, M44 for a custom amp project
Zx: Zx500, Zx450, Black Zx350
ZxTi: 4 Zx600Ti's, 1 Zx400Ti
Ti: 5 800.1's & 900.7 for a custom amp project. 1 1200.1, 1 1000.2
Tantrum: 2 1200.1's, 1 600.4, 1 500.2
XS: XS6600
Hi everyone I just joined this forum and l need 1 of the bass cube remote can anyone tell me how to order one of these I have recently bought PG basscube and it has came without the remote so I am desperate to get one to hear the improvements to my sound on the low frequencys.
Jacampb2 wrote: ↑Tue Sep 20, 2022 3:54 am
We still make them, but probably not fit much longer. I'm almost out of the specialty gain pot and I've not been able to source more.
I know this is a total shot in the dark but is there any chance you are still making the knobs? Mine finally died and I can't find replacements anywhere. All paths lead here.
Jacampb2 wrote: ↑Thu Oct 17, 2024 7:00 pm
We still make them. I found a new source for the gain pots, they were significantly more expensive, but we bought them and are still making remotes.
please my email is: ittechsecurecorp1863@outlook.com
