RMD ?
-
NOT 2 OLD YET
- Posts: 400
- Joined: Mon Mar 17, 2014 4:13 pm
- Location: The Windy City
RMD ?
I picked 1 up for my truck and after reading some older posts, it will not work with my ZBB34TI. MY Bad! Is it possible to hard wire the unit in and if so what are the color codes? Thanks Fellas!
Collection And Still Growing:
M-100, 50,2,44s, and 25
RT 66 #0840, Outlaw#1005, Bandit#1884, MQ430
MS2125, MS275, MS 2250 W/shroud 3MPS2500, 2 MPS2240 Custom MPS4740
EQ215, EQ215ix,EQ 230 W/TBAt, ZX600TI, 400TI, TI500.4
2 PLD1, MX2, 2 Leather Team PG Jackets
TBA (Dealer Display Empty Guts)10'XS Subs
AX204, 406 (New In Box)
Eclipse ECD413 + DSP1001 , 2 JL 8W6
Installed: PG MPS2500 and Modified By PG MQ430
ZBB34TI With ZRDT3, and RMD
Audison Bit 10
PG Elite and Sapphire 6.5 Comps
JL 13TW5 subs
M-100, 50,2,44s, and 25
RT 66 #0840, Outlaw#1005, Bandit#1884, MQ430
MS2125, MS275, MS 2250 W/shroud 3MPS2500, 2 MPS2240 Custom MPS4740
EQ215, EQ215ix,EQ 230 W/TBAt, ZX600TI, 400TI, TI500.4
2 PLD1, MX2, 2 Leather Team PG Jackets
TBA (Dealer Display Empty Guts)10'XS Subs
AX204, 406 (New In Box)
Eclipse ECD413 + DSP1001 , 2 JL 8W6
Installed: PG MPS2500 and Modified By PG MQ430
ZBB34TI With ZRDT3, and RMD
Audison Bit 10
PG Elite and Sapphire 6.5 Comps
JL 13TW5 subs
-
trickyricky
- Posts: 1653
- Joined: Sun May 06, 2012 8:01 am
Re: RMD ?
Should be easy, figure out which pins on the ZBB are the negative/ground and positive, buy the correct module jack for the cable end on your RMD and rewire it. I believe the RMD has four pin/positions so its two positives and two grounds.
-
NOT 2 OLD YET
- Posts: 400
- Joined: Mon Mar 17, 2014 4:13 pm
- Location: The Windy City
Re: RMD ?
My thought was hard wire it in to the system off of the main relay. That way it will turn off also. I am just not sure which color will go where to make it work correct.
Collection And Still Growing:
M-100, 50,2,44s, and 25
RT 66 #0840, Outlaw#1005, Bandit#1884, MQ430
MS2125, MS275, MS 2250 W/shroud 3MPS2500, 2 MPS2240 Custom MPS4740
EQ215, EQ215ix,EQ 230 W/TBAt, ZX600TI, 400TI, TI500.4
2 PLD1, MX2, 2 Leather Team PG Jackets
TBA (Dealer Display Empty Guts)10'XS Subs
AX204, 406 (New In Box)
Eclipse ECD413 + DSP1001 , 2 JL 8W6
Installed: PG MPS2500 and Modified By PG MQ430
ZBB34TI With ZRDT3, and RMD
Audison Bit 10
PG Elite and Sapphire 6.5 Comps
JL 13TW5 subs
M-100, 50,2,44s, and 25
RT 66 #0840, Outlaw#1005, Bandit#1884, MQ430
MS2125, MS275, MS 2250 W/shroud 3MPS2500, 2 MPS2240 Custom MPS4740
EQ215, EQ215ix,EQ 230 W/TBAt, ZX600TI, 400TI, TI500.4
2 PLD1, MX2, 2 Leather Team PG Jackets
TBA (Dealer Display Empty Guts)10'XS Subs
AX204, 406 (New In Box)
Eclipse ECD413 + DSP1001 , 2 JL 8W6
Installed: PG MPS2500 and Modified By PG MQ430
ZBB34TI With ZRDT3, and RMD
Audison Bit 10
PG Elite and Sapphire 6.5 Comps
JL 13TW5 subs
-
trickyricky
- Posts: 1653
- Joined: Sun May 06, 2012 8:01 am
Re: RMD ?
Am not familiar with those fancy fuse blocks, but I thought they had a remote terminal as well? Is the jack a RMD or RDDP? If its an RDDP then you might want to take a look at the PG info sheet on that.
