Distribution block

thingy · Post by **thingy** » Mon Jul 07, 2008 7:42 am

Hi guys
I need a distribution block that'll accept 1 0ga input and 2 2ga outputs - fused if possible and also waterproof would be nice - any ideas ?

Post by **Bfowler** » Mon Jul 07, 2008 8:53 am

2 2awg might be tricky....

what you might have to resort to is a 1/0 to a 4 x 4awg out.

then get 2 additional blocks that are 2 x 4awg to 1/0 and use them backwards

thingy · Post by **thingy** » Mon Jul 07, 2008 9:43 am

it's because i bought tristans M100 - now i need some bigger power wire and i got a length of 2 awg lying around so i figured - i'll add som 0awg from the battery split it to 2 2awg about 3 ft from the battery clamp and then i'm home free

- might have to fabricate some myself - will stainless steel be ok if i cant find any gold plated brass lying of the shelves ?

Post by **stipud** » Mon Jul 07, 2008 9:57 am

Just stuff the 2g in a 4g distro. I can fit 2g directly into my Ti500.4 without issues

Post by **Bfowler** » Mon Jul 07, 2008 9:57 am

you could just use a bolt and ring terminals....

HoseHead · Post by **HoseHead** » Mon Jul 07, 2008 2:31 pm

I have several PG Distro blocks here on the shelf.
These are distro blocks, not fuse holders.
Not waterproof.
All are new, never installed.

Unfused:
3 X 0 AWG in - 4 X 4 AWG out
1 X 0 AWG in - 2 X 2 AWG out

Fused:
3 X 0 AWG in - 2 X 0 AWG out (each "out" is double fused if needed - ANL)
1 X 0 AWG in - 2 X 4 AWG out (each "out" is separately fused - AGU)

I'll get some pics up later this evening, eh.......

HH

thingy · Post by **thingy** » Tue Jul 08, 2008 9:40 am

HH that might be something
Otherwise i found these :
http://cgi.ebay.co.uk/KnuKonceptz-1-0-G ... .m14.l1318
http://www.caraudiodirect.co.uk/stinger ... -1473.html
Any experience with those ? - i only have experience with PG and Audison stuff for wiring kits (Love PG but the Audison http://www.connectionaudison.com/produc ... sfd41c.htm sure feels nice in the fingers

what about the PG block on the pic ? what kind of connections does that have ?
Thnx guys

HoseHead · Post by **HoseHead** » Tue Jul 08, 2008 9:48 am

I have that one:

1 X 0 AWG in - 2 X 2 AWG out

I'll post a pic after business today.

HH

Post by **Bfowler** » Tue Jul 08, 2008 9:55 am

are you sure those are ^2awg?

i thought that block was 1/0 in 2x4awg + 2x8awg out

Post by **fuzzysnuggleduck** » Tue Jul 08, 2008 9:56 am

The distro in the picture has three 1/0AWG in / 2 x 4AWG and 2 x 8AWG out.

soth · Post by **soth** » Tue Jul 08, 2008 10:11 am

fuzzysnuggleduck wrote:The distro in the picture has three 1/0AWG in / 2 x 4AWG and 2 x 8AWG out.

I've got the same one and fuzzy is correct on the in/out at least according to the one i've got.

Post by **fuzzysnuggleduck** » Tue Jul 08, 2008 10:24 am

I'm using two of them