redone audi

thedeal7235 · Post by **thedeal7235** » Fri Nov 07, 2008 1:51 pm

heres a couple of pics with the audi -put the zx350/450 back in, if i get another 450/or 500(zx), ill swap that out for the 350=

thedeal7235 · Post by **thedeal7235** » Fri Nov 07, 2008 1:52 pm

forgot the pic

Post by **mhyde71** » Fri Nov 07, 2008 2:02 pm

Looks fricken killer dood! like it!

know what I had considered on doing, which would be neat...
see one of those PG badges you got... drill a couple 3/16" holes (or whatever size they are/works for the screws) for the badge to be on the Plexi of the DD10... I tried with one of mine, didnt make the holes, but simply layed it on it and looked pretty cool... but it does interfere with seeing in to each/every light on DD10's board

SolacE · Post by **SolacE** » Fri Nov 07, 2008 3:49 pm

Looks good. I was going to use my smaller surf board logos as drawer handles for a hidden drawer that would house my xover and dd5.

thedeal7235 · Post by **thedeal7235** » Fri Nov 07, 2008 4:08 pm

awesum ideas------

thedeal7235 · Post by **thedeal7235** » Fri Nov 07, 2008 5:25 pm

was tryn to put the mx3i in the center of the 2 amps, but once ud plug the rcas in(main input to the left of it, and 3 out to the right, wasnt enuff room, too close to the 450 ven, and that does get very hot

oldskoolmseriesfan · Post by **oldskoolmseriesfan** » Fri Nov 07, 2008 8:20 pm

Looks really nice. Wish I had that much PG gear

Just a suggestion seeing how this is in an Audi, have you thought of how to hide the wires and cables?,do you have enough clearance to conceal them with the seats when they are up?

Post by **VW337** » Fri Nov 07, 2008 9:08 pm

get 2 more of the PG logos and form your 4 rings Audi logo with them somewhere......

thedeal7235 · Post by **thedeal7235** » Sat Nov 08, 2008 12:07 am

oh i can tbelieve i didnt think of that -thanx vw337-btw the seats go up PERFECTLY, if you look under check my ride in september i took pics of the seats up-i do have 2 more pg emblems that size and one exactly like these except 10inches wide by 4.5 tall

joyride · Post by **joyride** » Sat Nov 08, 2008 7:02 am

Im just curious, but is the MX3 really needed? It looks as though you have the 450 running the fronts, nad the 350 on the subs. With the external outputs and highly variable crossovers, you can use the output on the 450 to pass the remaining low pass freq to the base cube and 350. Doing it this way provides a perfect X/O network between the amps. Also, as you change the freq on the first amp, the second is directly affected.

Your install looks good, and its a shame they dont make the DD10 in white. I loved the white ZX stuff. That reminds me, I will try to get you some pics of my white 450 for you.

thedeal7235 · Post by **thedeal7235** » Sat Nov 08, 2008 7:17 am

the 450 is for 2 sets of ti 6.5, and the 350 is for one set of ti tweets, i like the mx, b/c it send a 24db/octave signal to my rsd 1200.1 in the back, although u cant bypass the rsd1200.1 internal, but i notice its alot cleaner with it; guess ur right, I could use the internal, just have always used external , b/c pg amp xovers, in my experience, have always been more prone to pot issues, rubbing the lid, going bad, figure less stress on the amp, btw, is that ur vette for ur avatar?i have pics of the rsd 1200.1 under install/your ride from september showing my rsd 1200.1--yeaph send me a pic-another memeber and i believe have a deal worked out, as of yesterday, but i havent heard back from him, ill send him another email-

Irongoats · Post by **Irongoats** » Mon Nov 10, 2008 4:35 am

Very nice.

marko · Post by **marko** » Mon Nov 10, 2008 8:39 am

joyride wrote:Your install looks good, and its a shame they dont make the DD10 in white.

i will have one very soon, a custom one with a twist