My AlfaRomeo Hi-fi (work in progress...)
My AlfaRomeo Hi-fi (work in progress...)
Firts an animated .gif of my car
An simplified diagram connections
The audio system it's voted to the Sound Quality but sometimes does not disdain the bass line.
It's an simple 2way+sub, managed completely on active from its source (regards crox and temporal delays and multiamp)
In addition there is also a non-invasive rear facing (consisting only of mw) for passengers.
The Component:
Battery: Exide Maxxima 900DC
PowerCap: Helix Ca33 da 0,33F
Head source : Alpine dva9965r
Front
Tw : Microprecisione Z
WF: Microprecision Z 170K
Amp Front: Phoenix Gold Outlaw
Rear
MW: Coral PRF160
Amp Rear Phoenix Gold Bandit
SubWoofer: Boston 10.5LF sealed box 14L
Amp SW: Orion Hcca 250 V2
Signal Cable: knukonceptz Krystal
Speaker Wire: thender 52-012 for Mw, audioson Sonus for tw e Sonus 212 for SW
Also, this is a 1,5F capacitor and a circuit for the delayed ignition and shutdown of electronic part (antibump).
An simplified diagram connections
The audio system it's voted to the Sound Quality but sometimes does not disdain the bass line.
It's an simple 2way+sub, managed completely on active from its source (regards crox and temporal delays and multiamp)
In addition there is also a non-invasive rear facing (consisting only of mw) for passengers.
The Component:
Battery: Exide Maxxima 900DC
PowerCap: Helix Ca33 da 0,33F
Head source : Alpine dva9965r
Front
Tw : Microprecisione Z
WF: Microprecision Z 170K
Amp Front: Phoenix Gold Outlaw
Rear
MW: Coral PRF160
Amp Rear Phoenix Gold Bandit
SubWoofer: Boston 10.5LF sealed box 14L
Amp SW: Orion Hcca 250 V2
Signal Cable: knukonceptz Krystal
Speaker Wire: thender 52-012 for Mw, audioson Sonus for tw e Sonus 212 for SW
Also, this is a 1,5F capacitor and a circuit for the delayed ignition and shutdown of electronic part (antibump).
HeadUnit:Dva-9965r
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
Soundproofing
Thanks to my brother.
removal of the panels in Tar
cleaning
cut and shaped steel
after clean the surface with achool and degreaser, I applied to two materials to make heavy the structure and eliminate the reflections
First Butyflex T250/AL,
Thanks to my brother.
removal of the panels in Tar
cleaning
cut and shaped steel
after clean the surface with achool and degreaser, I applied to two materials to make heavy the structure and eliminate the reflections
First Butyflex T250/AL,
HeadUnit:Dva-9965r
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
little cold beer and restart
After applying the material, proceed with the preparation of Brax eXvibration Pro
inside part
external part
retail spaces left for cables and movement opening handle
here is the effect
After applying the material, proceed with the preparation of Brax eXvibration Pro
inside part
external part
retail spaces left for cables and movement opening handle
here is the effect
HeadUnit:Dva-9965r
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
Having laid out the last hand of Brax I have left everything to dry for 12 hours.
After I applied the dynaxorb at the mw
finally applied the mdf ring
re-mounted door
After I applied the dynaxorb at the mw
finally applied the mdf ring
re-mounted door
HeadUnit:Dva-9965r
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
then the external folder I have dealt more with isolmant (polyethylene foam closed-cell crosslinked physically)
with the same material had been isolated from the roof
with the same material had been isolated from the roof
HeadUnit:Dva-9965r
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
- cyberpunky
- Posts: 67
- Joined: Thu Jun 18, 2009 6:43 am
- Location: Melbourne
My False-bottom β version.
Ok there are no hope, destroy and restart.....
wood
drill
air compressor
first coat of paint
holes and test
Ok there are no hope, destroy and restart.....
wood
drill
air compressor
first coat of paint
holes and test
HeadUnit:Dva-9965r
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
Excellent install! I'd be a little nervous about that distribution block being unprotected though. Don't want anything shorting out.
XS2300, XS2500, XS2300, X200.4, X100.2, Ti21000.4, Roadster 66
I'm gonna become a civil engineer. I'm gonna design septic tanks for playgrounds. Little kids can take shits! You idiot, what the hell do you do?
I'm gonna become a civil engineer. I'm gonna design septic tanks for playgrounds. Little kids can take shits! You idiot, what the hell do you do?
Thanks all.
All this work it' handmade by myself (and in same point isn't good )
@Misfire: Hum, at the moment thw sub it's in this position
(sometimes I need to remove it)
@Bfowler: Yes the distribution block it's made with the help of my friend that have an CNC machine.
@joerg & ttocs: The structure it's
1 layer of Butyflex T250/AL link to the datasheet (sorry only on ITA)
2 -3 layer Brax eXvibration Pro
4 layer (only on external folder) Isolmant similar at the Vinyl product.
All this work it' handmade by myself (and in same point isn't good )
@Misfire: Hum, at the moment thw sub it's in this position
(sometimes I need to remove it)
@Bfowler: Yes the distribution block it's made with the help of my friend that have an CNC machine.
@joerg & ttocs: The structure it's
1 layer of Butyflex T250/AL link to the datasheet (sorry only on ITA)
2 -3 layer Brax eXvibration Pro
4 layer (only on external folder) Isolmant similar at the Vinyl product.
HeadUnit:Dva-9965r
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
FA: Microprecision Z
FP: Microprecision Z
Sub:Boston Pro 10.5LF 2Ohm
Amply FA: Phoenix Gold Outlaw 1845
Amply Fp: Phoenix Gold Bandit
Amply SW: Orion HCCA 250 V2
- phoenixcat
- Posts: 68
- Joined: Sun Mar 02, 2008 10:42 am
why go out of the way then do the tweeters like that in the a-pillar (angled down....way the hell off axis)
James Shields
[email][email protected][/email]
[url]http://www.northolmstedperformance.com[/url]
[img]http://www.northolmstedperformance.com/images/Business_card_front.sized.jpg[/img]
[email][email protected][/email]
[url]http://www.northolmstedperformance.com[/url]
[img]http://www.northolmstedperformance.com/images/Business_card_front.sized.jpg[/img]