"The Outlaw" install!

longboard · Post by **longboard** » Sun Mar 28, 2010 2:40 am

looks very nice marko i need to get on with the peugeot but been so busy at work
you talked nath into building again yet!!

marko · Post by **marko** » Sun Mar 28, 2010 2:52 am

Tiger wrote:Forgive me for asking.. what sub is that?

And THAT is a truely brilliant install! Super clean.. and I'm tipping that the sound will match the look, no doubt,

it's a velodyne, the only part of the system that works at the moment! front end not sorted yet..

paintguy · Post by **paintguy** » Sun Mar 28, 2010 6:11 am

longboard wrote:you talked nath into building again yet!!

He's just been round to borrow a compressor off me - so he must be up to something

marko · Post by **marko** » Sun Mar 28, 2010 6:14 am

paintguy wrote:
longboard wrote:you talked nath into building again yet!!
He's just been round to borrow a compressor off me - so he must be up to something

oh, the never ending install

might be done for the next world cup in 2014!

when i start something i don't piss around i get on with it and complete but then again i'm not a perfectionist lika nath

shaheen · Post by **shaheen** » Sun Mar 28, 2010 6:21 am

Nice one Marko , except the sig should now say

2 x outlaws in boot.

Post by **Eric D** » Sun Mar 28, 2010 6:43 am

I am impressed. That is so clean it makes me wish I had a car to put an install in. I especially like how the wires go through grommets in the sides, even though none of that is seen with the cover on. Attention to details is what I think makes an installation great.

paintguy · Post by **paintguy** » Sun Mar 28, 2010 7:12 am

marko wrote: oh, the never ending install might be done for the next world cup in 2014!

Don't tell me that - he's offered some help and advice with mine in return. I know it won't be a quick job with me involved, but I'd like it finished for the end of the century

Have you got any build pics then Mark? I love the finished product, but I'm always interested in how it got there.

longboard · Post by **longboard** » Sun Mar 28, 2010 7:16 am

[/quote]
oh, the never ending install

might be done for the next world cup in 2014!

when i start something i don't piss around i get on with it and complete but then again i'm not a perfectionist lika nath

[/quote]

that the trouble with me i get something done then look at it and think i could do it better but when its done it should be good lol
im not a perfectionist but i like things right !!

Post by **Bfowler** » Sun Mar 28, 2010 9:36 am

so i see another 4awg coming out of the bottom of your ti fuse block. is that going to another block to power your accessories?

marko · Post by **marko** » Sun Mar 28, 2010 9:41 am

Bfowler wrote:so i see another 4awg coming out of the bottom of your ti fuse block. is that going to another block to power your accessories?

that goes to the dd10 that resides in the right hand side cubby hole, on the left side lives the focal crossblock. i'm not quite finished with trimming these bits so no pics yet.. got to add an rmd in there too just to finish things off.

Post by **ttocs** » Sun Mar 28, 2010 11:47 am

wow did you built the angled part between the floor and the woofer? Is it fiberglass or something else?

marko · Post by **marko** » Sun Mar 28, 2010 12:06 pm

ttocs wrote:wow did you built the angled part between the floor and the woofer? Is it fiberglass or something else?

initially i made it in one piece but then realised i'd never be able to trim it in one piece

so split it in 2 and trimmed them seperately..

also made a perspex ring to add some lighting at a later date, will do the same on the amps, there enough room to have a couple of strips of perspex/leds in there as there's about 5mm gap.

Post by **ttocs** » Sun Mar 28, 2010 7:58 pm

I figured but was not sure. I had a similar problem on the top panel of my truck where it was a strange shape that wood just wouldn not do. I found that after making the wood braces that the material wouldn't lay straight enough which was going to result with alot of filling and sanding which looks like you had the same issue. I actually covered the wood braces with a piece of posterboard trimmed to fit and stapled in place, then layed my material on top of it. I saturated them both with resin to make one piece and had very little sanding as it layes straight on top of the cardboard.

I like the smooth transition between the two, as simple as it looked I knew it was not that easy....... It often the little parts that make it hard huh?

Post by **AVICJR** » Mon Mar 29, 2010 10:55 am

marko wrote:might be done for the next world cup in 2014!

Marko, same as your last install, absolutely beautiful! Fuzzy (Roldy) and I were talking about how we both were impressed with this one. CLEAN!!!

What team(s) do you support? We Americans are looking for a WC 1950 repeat.

marko · Post by **marko** » Mon Mar 29, 2010 10:58 am

AVICJR wrote:What team(s) do you support? We Americans are looking for a WC 1950 repeat.

EDIT- England of course!!

Post by **AVICJR** » Mon Mar 29, 2010 11:04 am

marko wrote:
AVICJR wrote:What team(s) do you support? We Americans are looking for a WC 1950 repeat.

EDIT- England of course!!

Sorry Mate, meant club wise??

Post by **Bfowler** » Mon Mar 29, 2010 11:15 am

westham son. they are fighting for their premier lives!